{"title":"Ethernet Surge Protectors","description":"\u003cp data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\" style=\"font-weight: 400;\" data-mce-style=\"font-weight: 400;\"\u003eDamaging electrostatic discharge attacks and surges are diverted to \u003ca href=\"https:\/\/www.tupavco.com\/products\/ethernet-surge-protector\" title=\"ethernet surge protectors \"\u003eethernet surge protectors\u003c\/a\u003e and the device will immediately conduct the energy to earth to limit the voltage to levels which are unlikely to cause damage to the electrical equipment it's protecting. \u003c\/span\u003eWithout adequate protection, there is the potential for downtime and this can cause major issues in your place of work, for example. Protect yourself today -see our range of ethernet surge protectors below.\u003c\/p\u003e","products":[{"product_id":"ethernet-surge-protector","title":"Tupavco TP302 Ethernet Surge Protector PoE++ Gigabit RJ45 Lightning Suppressor","description":"\u003ch4\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B00805VUD8\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: 741360887824\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP302\u003c\/em\u003e\u003cbr\u003e\n\u003c\/h4\u003e\n\u003ch6\u003e\u003cimg title=\"English\" height=\"30px\" width=\"30px\" src=\"https:\/\/www.worldoftales.com\/media\/flags\/United_States3.png\"\u003e\u003c\/h6\u003e\n\u003cp\u003e\u003cb\u003eEthernet Surge Protector\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e is a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning).\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"font-weight: 400;\"\u003eEthernet Surge Suppressor TP302 use a \u003c\/span\u003e\u003cb\u003eGas Discharge Tube\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as network hub, switch, router, modem, bridge, repeater, or any part of ISP (internet service provider) network or LAN system.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePOE Surge Protector\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e allows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP302 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The ethernet surge protector PoE supports both \u003c\/span\u003e\u003cb\u003eMode\u003c\/b\u003e \u003cb\u003eA (Pins 1,2+ 3,6-) and B\u003c\/b\u003e \u003cb\u003e(7,8+ 4,5-)\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e of the \u003c\/span\u003e\u003cb\u003e802.3af \u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003estandard for supplying DC power. \u003c\/span\u003e\u003cb\u003e802.3af (PoE)\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e can deliver up to 15.4 watts per port over Cat5 cables with 12.95W assured to be available at the powered device, while \u003c\/span\u003e\u003cb\u003e802.3bt (PoE++)\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e can deliver up to 30 watts over network cables with 25.5 watts available to devices. For that reason, PoE Plus is also known as \u003c\/span\u003e\u003cb\u003eHigh PoE\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e. Ethernet surge protector allows PoE injected into the LAN cable at a voltage up to 60 volts DC, and typically 48 VDC is used.\u003c\/span\u003e\u003c\/p\u003e\n\u003cdiv data-cel-widget=\"aplus-launchpad-brand-description-left\" class=\"celwidget aplus-module launchpad-brand-description-left\"\u003e\n\u003cdiv class=\"a-section a-spacing-top-mini launchpad-module launchpad-module-brand-description-left\"\u003e\n\u003cdiv class=\"a-section launchpad-text-left-justify\"\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eMounting flange\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon the both sides of lightning suppressor allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cspan style=\"font-weight: 400;\"\u003eThe unit’s data rate\u003c\/span\u003e \u003cspan style=\"font-weight: 400;\"\u003eof \u003c\/span\u003e\u003cb\u003eGigabit 10\/100\/1000 (GbE) \u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003etransfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"font-weight: 400;\"\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet \u003c\/span\u003e\u003cb\u003eground wire\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e (12 Inch - 16 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e\u003cspan style=\"font-weight: 400;\"\u003e\u003c\/span\u003e\u003c\/i\u003e\u003cspan style=\"font-weight: 400;\"\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables. The arrester is housed in a \u003c\/span\u003e\u003cb\u003ecast aluminum\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e enclosure. The metal housing allows \u003c\/span\u003e\u003cb\u003eshielded \u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003ecurrent to be passed through the metal case of the network surge protector.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"font-weight: 400;\"\u003eThe \u003c\/span\u003e\u003cb\u003eLine-to-Line\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e ethernet surge protection mode helps protect against short circuits between different nodes of the network system while the \u003c\/span\u003e\u003cb\u003eLine-to-Ground\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e mode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of \u003cstrong\u003e20\u003c\/strong\u003e\u003c\/span\u003e\u003cb\u003eKA\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e defines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan style=\"font-weight: 400;\"\u003eOnce the surge voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A \u003c\/span\u003e\u003cb\u003ebidirectional clamping\u003c\/b\u003e\u003cspan style=\"font-weight: 400;\"\u003e on CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eNetwork surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cp\u003eInvesting in a small, easy to install surge protector with all of the needed features and proven reliability can be the safest and most cost-effective solution for protecting your whole Ethernet network.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eNominal Discharge Current (8\/20μs):  20 KA\u003cbr\u003e\u003cspan\u003eNominal PoE voltage : \u0026lt;60V\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003e\u003cmeta charset=\"utf-8\"\u003ePoE current: 1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003cbr\u003ePoE Mode Support Mode A and B for Power\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eImpedance 100 ohms\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eTested standards IEC 61643-21, IEC61000-4-5\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eClamping Voltage Line-Ground: 72 Volts\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eClamping Voltage Line-Line: 72 Volts\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eProtection Modes Line-Line, Line-Ground\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eOutside Dimensions (W*L*H) 26*26*70 mm\u003cbr\u003e\u003c\/span\u003eWeight: 60 g\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch6\u003e\u003cimg title=\"French\" height=\"30px\" width=\"30px\" src=\"https:\/\/www.worldoftales.com\/media\/flags\/France3.png\"\u003e\u003c\/h6\u003e\n\u003cp\u003e\u003cb\u003eProtecteur de surtension d’Ethernet\u003c\/b\u003e est un dispositif anti-surtension (SPD) qui s’insère sur un câble RJ45 CAT6\/CAT5\/CAT5e pour prévenir tout endommagement de l’équipement informatique en réseau. Le dispositif protège contre les surtensions dangereuses comme les coups de foudre directs les crêtes de tension ou les survoltages PoE. Malgré la protection première (une frappe directe sur la ligne), le parafoudre procure également une protection secondaire, qui arrête les surtensions electromotrices (foudre proche d’Ethernet). \u003cbr\u003e\u003cbr\u003eLe suppresseur de foudre Ethernet TP302 protège à plusieurs niveaux, utilisant le \u003cb\u003etube de décharge de gaz\u003c\/b\u003e (GDT) sur les 4 paires (8 fils), les éclateurs, les résistances en séries de limitation de courant et le réseau de diodes de faibles capacités à l’étape finale. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eLes tubes de décharge de gaz\u003c\/b\u003e (GDTs) ont été mis au point pour surmonter les inconvénients des protecteurs basés sur les diodes comme la capacité de gestion de l’énergie. Il convient pratiquement à toutes les surtensions aussi bien de haute que de faible capacité. Les surtensions sont interceptées par le parafoudre à tubes de décharge de gaz qui procure une performance de contrôle rigoureux d’étincelles de décharge. Le suppresseur de foudre Ethernet TP302 utilise le tube de décharge de gaz (GDT) sur les 4 paires (8 fils). Les tubes de décharge de gaz dissipent les transitoires de tension par gaz plasmagène qui maitrise la tension excessive de la tension d’entrée et la libère en sécurité. De cette manière il garantit la sécurité d’un large éventail de composants précieux comme l’interrupteur, le routeur, le modem, le bridge, le répéteur ou n’importe quelle composante du réseau Internet. \u003cbr\u003e\u003cbr\u003e\u003cb\u003eLe transfert de Gigabit GbE 10\/100\/1000\u003c\/b\u003e, permet à notre protecteur de surtensions Ethernet de prendre en charge un débit d’1 Gigabit par seconde (Gbps – 1000 Mbps) qui n’a aucune incidence sur la vitesse et la performance du réseau informatique local. \u003cbr\u003e\u003cbr\u003eLe parafoudre PoE permet à un seul câble RJ-45 d’assurer la fourniture de la connexion d’alimentation et de données aux dispositifs comme le point d’accès sans fil, le périphérique IP, la caméra de sécurité, le téléphone VoIP, l’ordinateur etc. Le parafoudre TP302 est conçu pour protéger l’équipement d’alimentation électrique (PSE) relié au réseau contre les surtensions transitoires. Notre protecteur de surtensions Ethernet PoE prend en charge le \u003cb\u003emode A (Pins 1,2+ 3,6-)\u003c\/b\u003e et \u003cb\u003ele mode B (7,8+ 4,5-)\u003c\/b\u003e de la norme 803.3af pour l’alimentation DC. \u003cb\u003e(PoE) 802.3af\u003c\/b\u003e fournit jusqu’à 15,4 watts par port grâce aux câbles CAT5 et garantit 12,95 W disponibles pour le dispositif alimenté, tandis que le \u003cb\u003e802.3bt\u003c\/b\u003e (PoE++) fournit jusqu’à 30 watts grâce aux câbles de réseau et 25,5 watts disponibles pour les dispositifs. C’est pourquoi PoE++ est également connu comme un \u003cb\u003ePoE de Haute puissance\u003c\/b\u003e. Le protecteur Ethernet permet l’utilisation de PoE branché à un câble LAN au voltage jusqu’à 60 volts DC, et on utilise habituellement 48 VDC. \u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003ePour fonctionner, le parafoudre Ethernet doit être correctement mis à la terre. Le \u003cb\u003efil de terre\u003c\/b\u003e Ethernet (28 cm - 16 AWG) sur le dispositif anti-surtension doit être relié à la terre par le plus court chemin. Le surplus d’électricité va suivre la voie de moindre résistance. Dans la plupart des cas, la barre collectrice de terre sur un panneau électrique ou un coffret de réseau Rack est déjà mise à la terre ce qui est généralement le moyen le plus facile. Le protecteur de surtensions RJ-45 peut également être mis à la terre en utilisant le bloc de mise à la terre du panneau électrique, la tige de mise à la terre ou la borne de la prise la plus proche en reliant le fil de terre au trou circulaire de mise à la terre sur une vis centrale de prise de terre. \u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eLes brides de fixation\u003c\/b\u003e sur les deux côtés du dispositif anti-surtension permettent de fixer le boîtier facilement, sur un mur, un tableau électrique, une armoire de réseau ou un Rack à l’aide de vis (non fournies). \u003cbr\u003e\u003cbr\u003eLe parafoudre peut être utilisé avec des câbles à paire torsadée, non blindés (UTP), ou standards (STP). Le dispositif de protection est logé dans un boîtier en aluminium. L’enveloppe métallique permet au courant \u003cb\u003eisolé\u003c\/b\u003e de passer à travers la boîte métallique de notre dispositif anti-surtension. \u003cbr\u003e\u003cbr\u003eLe mode de protection contre les surtensions Ethernet \u003cb\u003eligne-à-ligne\u003c\/b\u003e protège contre les courts circuits entre les différents nœuds du système de réseau alors que le mode de protection \u003cb\u003eligne-terre\u003c\/b\u003e protège contre les courts circuits entre un nœud de réseau et la terre. Comme on ne peut pas savoir à quel endroit la surtension transitoire va survenir, la protection des deux modes garantit la réduction du risque d’endommagement. Le courant nominal de décharge de \u003cb\u003e5KA\u003c\/b\u003e définit la valeur maximale du courant qui peut passer par le SPD avec une oscillation de 8\/20μs microseconde. Le parafoudre RJ45 reste fonctionnel après 15 surtensions. \u003cbr\u003e\u003cbr\u003eQuand la tension Ethernet du dispositif anti-surtension excède la puissance autorisée, le protecteur « commence à serrer » et à conduire l’énergie directement vers le système de mise à la terre du réseau électrique. Le \u003cb\u003eserrage bidirectionnel\u003c\/b\u003e sur le CAT5 du parafoudre autorise le niveau au-dessus et le niveau au-dessous de la tension de référence en arrêtant la tension qui peut causer des dommages. \u003cbr\u003e\u003cbr\u003eLe parafoudre Ethernet va dans les deux sens (Entrée\/Sortie) et le câble du signal source entrant peut être raccordé de n’importe quel côté. Le côté du dispositif où se situe votre équipement n’a aucune importance. Mais, le protecteur de surtension protégera seulement l’équipement du réseau situé du côté opposé à l’endroit où survient l’excès de tension. Si vous souhaitez protéger vos appareils des deux côtés, nous recommandons de poser un parafoudre de chaque côté du câble RJ45 dans la topologie de votre réseau. \u003cbr\u003e\u003cbr\u003eInvestir dans un dispositif anti-surtension de petite taille, facile à fixer, qui présente toutes les caractéristiques requises en plus d’être d’une fiabilité reconnue, est le moyen le plus sûr et le plus économique pour protéger la totalité de votre réseau Ethernet. \u003cbr\u003e\u003cbr\u003eCourant nominal de décharge (8\/20μs) :5KA \u003cbr\u003eVoltage nominal PoE: \u0026lt;60V \u003cbr\u003eCourant PoE jusqu’à:\u003cspan\u003e 1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003c\/span\u003e\u003cbr\u003eMode PoE : prend en charge mode A et B pour alimentation \u003cbr\u003eImpédance 100 ohms \u003cbr\u003eNormes testées IEC 61643-21, IEC61000-4-5 \u003cbr\u003eFixation du voltage ligne-terre: 72 Volts \u003cbr\u003eFixation du voltage ligne-ligne: 72 Volts \u003cbr\u003eModes protection ligne-ligne, ligne-terre \u003cbr\u003eTempérature de fonctionnement – 40 °C (-40°F) to +80°C (+176°F) \u003cbr\u003eDimensions extérieures (L*L*H) 26*26*70 mm \u003cbr\u003ePoids : 60 g\u003c\/p\u003e\n\u003ch6\u003e\u003cimg title=\"Italian\" height=\"30px\" width=\"30px\" src=\"https:\/\/www.worldoftales.com\/media\/flags\/Italy3.png\"\u003e\u003c\/h6\u003e\n\u003cp\u003eLo scaricatore di sovratensione Ethernet è un dispositivo di protezione inserito inline su un cavo RJ45 CAT6\/CAT5\/CAT5e che protegge l’attrezzatura elettronica da danni dovuti a sbalzi di corrente.\u003c\/p\u003e\n\u003cp\u003eGli sbalzi elettrici da cui questo device protegge i dispositivi includono scariche dirette causate da fulmini, picchi di voltaggio, o sovratensioni PoE. Oltre alla protezione primaria (una scarica diretta alla linea), questo scaricatore offre anche una protezione secondaria, che arresterà le sovratensioni indotte dai campi elettromagnetici.\u003c\/p\u003e\n\u003cp\u003e[Il soppressore di sovratensioni Ethernet TP302 offre una protezione multipla utilizzando un \u003cstrong\u003etubo a scarica di gas\u003c\/strong\u003e (GDT) su 4 coppie (8 cavi), spinterometro, resistori in serie limitanti di corrente, e una matrice di diodi a bassa capacità nello stadio finale.]\u003c\/p\u003e\n\u003cp\u003eI \u003cstrong\u003etubi a scarica di gas\u003c\/strong\u003e (GDT) sono sviluppati per superare alcuni degli svantaggi dei protettori basati su diodo, quali la capacità di gestione dell’energia, e sono adattabili a quasi tutte le sovratensioni, sia ad alta che a bassa frequenza. Queste ultime possono essere intercettate da uno scaricatore con tubi a scarica di gas, che fornisce un rigoroso controllo della scarica. Il soppressore di sovratensione Ethernet TP305 utilizza un tubo a scarica di gas su tutte e 4 le coppie (8 cavi). Questi dissipano il voltaggio transitorio tramite uno scaricatore a plasma di gas che trattiene l’eccesso di voltaggio nella corrente elettrica in entrata e la rilascia in maniera sicura.  Garantisce la sicurezza di un’ampia gamma di componenti di valore quali switch, router, modem, bridge, ripetitori o qualsiasi altro dispositivo di rete.\u003c\/p\u003e\n\u003cp\u003eLa velocità di trasmissione a \u003cstrong\u003e10\/100\/1000 Gigabit\u003c\/strong\u003e del nostro limitatore di sovratensione supporta un velocità massima ultraveloce di 1 Gigabit a secondo (Gbps – 1000 Mbps), e non  influenza in alcun modo le prestazioni di velocità della rete locale.\u003c\/p\u003e\n\u003cp\u003eIl \u003cstrong\u003eprotettore\u003c\/strong\u003e \u003cstrong\u003edi sovratensione \u003c\/strong\u003e\u003cstrong\u003ePower over Ethernet (\u003c\/strong\u003ePoE) permette ad un singolo cavo RJ-45 di fornire sia connessione dati che elettricità a dispositivi quali wireless access point, IP e telecamere di sicurezza, telefoni VoIP, computer e altri dispositivi. Il protettore TP302 è progettato per proteggere le apparecchiature elettriche connesse ad una rete da sovratensioni improvvise. Questo dispositivo supporta entrambe le \u003cstrong\u003emodalità\u003c\/strong\u003e \u003cstrong\u003eA (Pins 1,2+ 3,6-) e B\u003c\/strong\u003e \u003cstrong\u003e(7,8+ 4,5-) \u003c\/strong\u003edegli standard della norma\u003cstrong\u003e 802.3af \u003c\/strong\u003esulla corrente continua\u003cstrong\u003e. \u003c\/strong\u003eLa \u003cstrong\u003e802.3af (PoE) \u003c\/strong\u003epuò fornire fino a 15.4 watts per porta su cavi Cat 5 con 12.95W disponibili sul dispositivo alimentato, mentre la\u003cstrong\u003e 802.3bt (PoE++) \u003c\/strong\u003epuò fornire 30 watt sui cavi della rete con 25.5 watt disponibili ai dispositivi. Per questa ragione, PoE++ è conosciuto anche come \u003cstrong\u003eHigh PoE\u003c\/strong\u003e. La protezione Ethernet consente l'iniezione di PoE nel cavo LAN a una tensione fino a 60 volt CC, e in genere viene utilizzato a 48V CC.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003ePer funzionare, il protettore di sovratensione deve essere correttamente installato.  Il cavo di messa a terra Ethernet (28 cm – 2 mm diam.) deve essere collegato a terra tramite il cammino più corto. L’eccesso di elettricità seguirà il percorso di minor resistenza. Nella maggior parte dei casi, una blindosbarra su un pannello elettrico o in un rack di rete sono già installati, ed è solitamente il modo migliore per effettuare la messa a terra. Altre opzioni sono il blocco di messa a terra sul pannello dell'interruttore, la vergella di messa a terra o il terminale della presa più vicina, collegando il cavo al foro circolare dell'uscita della vite centrale.\u003c\/p\u003e\n\u003cp\u003eLe \u003cstrong\u003eflange di montaggio\u003c\/strong\u003e su entrambi i lati permettono un’installazione facile sulla parete, su un pannello di rete, su un case del computer, o su un rack tramite viti (non incluse).\u003c\/p\u003e\n\u003cp\u003eIl protettore di sovratensione può essere utilizzato con cavi twisted pair (doppino ritorto) o cavi schermati. Lo scaricatore è alloggiato in un case in \u003cstrong\u003ealluminio pressofuso\u003c\/strong\u003e. L'alloggiamento metallico consente di far passare la corrente \u003cstrong\u003eschermata\u003c\/strong\u003e attraverso la case metallica del dispositivo di protezione.\u003c\/p\u003e\n\u003cp\u003eLa modalità di protezione di sovratensione line-to-line aiuta a proteggere contro cortocircuiti tra diversi nodi della rete, mentre la modalità line-to-ground protegge contro cortocircuiti tra terra e nodi di rete. Siccome non si sa dove si verificherà il transitorio, avere protezione in entrambe le modalità assicura che i danni siano minimizzati. La Corrente Nominale di Scarica di 5KA definisce il picco di valore della corrente che può passare attraverso lo scaricatore di corrente con una forma d’onda di 8\/20μs microsecondi in cui lo scaricatore di sovratensione rimarrà in funzione dopo 15 picchi di corrente.\u003c\/p\u003e\n\u003cp\u003eUna volta che la tensione del limitatore di sovratensione supera il valore nominale, \"inizia il serraggio\" e comincia a condurre energia direttamente al sistema di messa a terra. Un \u003cstrong\u003eserraggio bidirezionale\u003c\/strong\u003e sul protettore di sovratensione  permette di uniformare a livelli superiori o inferiori rispetto alla tensione di riferimento, bloccando la tensione che potrebbe causare danni.\u003c\/p\u003e\n\u003cp\u003eIl surge protector Ethernet funziona in entrambe le direzioni (IN\/OUT), per cui il cavo del segnale di ingresso può essere collegato su entrambi i lati. Non importa dietro quale lato si trovi l’apparecchiatura, ma il surge protector proteggerà solo i dispositivi di rete sul lato opposto a quello dove avviene la sovratensione. Per proteggere i dispositivi su entrambi i lati, è raccomandabile avere un dispositivo di protezione su ogni lato del cavo RJ45 nella topologia di rete.\u003c\/p\u003e\n\u003cp\u003eInvestire in un protettore di sovratensione piccolo, facile da installare, e dotato di importanti funzioni e affidabilità, può essere il modo più semplice ed economico per proteggere la tua intera rete Ethernet.\u003c\/p\u003e\n\u003cp\u003eCorrente nominale di scarica (8\/20μs):  5 KA\u003cbr\u003eVoltaggio nominale PoE: \u0026lt;60V\u003cbr\u003eCorrente PoE fino a: \u003cspan\u003e1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003c\/span\u003e\u003cbr\u003eModalità Supporto PoE Mode A e B per Elettricità\u003cbr\u003eImpedenza 100 ohms\u003cbr\u003eStandard IEC 61643-21, IEC61000-4-5\u003cbr\u003eClamping Voltage Line-Ground: 72 Volts\u003cbr\u003eClamping Voltage Line-Line: 72 Volts\u003cbr\u003eModalità Protezione Line-Line, Line-Ground\u003cbr\u003eTemperatura in funzione da -40°C (-40°F) a +80°C (+176°F)\u003cbr\u003eDimensioni esterne (L*L*A) 26*26*70 mm\u003cbr\u003ePeso: 60 g\u003c\/p\u003e\n\u003ch6\u003e\u003cimg title=\"German\" height=\"30px\" width=\"30px\" src=\"https:\/\/www.worldoftales.com\/media\/flags\/Germany3.png\"\u003e\u003c\/h6\u003e\n\u003cp\u003e\u003cstrong\u003eDer Ethernet Surge Protector ist ein Überspannungsschutzgerät (SPD), das inline an ein RJ45 CAT6\/CAT5\/CAT5e Kabel angeschlossen wird, um vor Schäden an einer Vielzahl wertvoller elektronischer Netzwerkgeräte zu schützen.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eDas Gerät schützt vor starken Überspannungen wie direkte Blitzeinschläge, Spannungsspitzen oder PoE-Überspannungen. Trotz des primären Schutzes (direkter Schlag auf eine Leitung) bietet der Gewitterableiter auch einen sekundären Schutz, der EMV-induzierte Überspannungen verhindert.\u003c\/p\u003e\n\u003cp\u003eDer Ethernet-Überspannungsschutz TP302 bietet mehrstufigen Schutz durch ein Gasentladungsrohr (GDT) an allen 4 Paaren (8 Drähte), Funkenstrecken, strombegrenzende Widerstände und eine Diodenanordnung mit niedriger Kapazität in der Endstufe.\u003c\/p\u003e\n\u003cp\u003eEs wurden \u003cstrong\u003eGasentladungsröhren (GDTs)\u003c\/strong\u003e entwickelt, um einige Nachteile von Dioden basierten Protektoren zu vermeiden, wie z.B. die Fähigkeit zur Energieverarbeitung. Sie eignen sich für fast alle Überspannungen, ob hoch- oder niederfrequent, sie können von einem Gasentladungsröhren-Überspannungsableiter abgefangen werden, sodass sie eine rigorose Funkenentladungskontrolle ermöglichen. Der Ethernet-Überspannungsschutz TP302 verwendet ein Gasentladungsrohr (GDT) an allen 4 Paaren (8 Drähte). Die Gasentladungsröhren leiten den Spannungsübergang durch ein Plasmagas ab, sodass die überschüssige Spannung als Energie genutzt und sicher abgegeben wird. Die Sicherheit einer Vielzahl von wertvollen Geräten wie Schalter, Router, Modem, Parallelschaltung, Verstärker etc. wird gewährleistet.\u003c\/p\u003e\n\u003cp\u003eDie Gigabit- Überspannungsschutzrate von \u003cstrong\u003e10\/100\/1000 Gigabit (GbE) \u003c\/strong\u003eunterstützt eine ultraschnelle maximale Datenrate von 1 Gigabit pro Sekunde (Gbps - 1000 Mbps) und beeinträchtigt nicht die Geschwindigkeitsleistung im lokalen Netzwerk.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDer POE Überspannungsschutz\u003c\/strong\u003e ermöglicht es, ein einzelnes RJ45-Kabel zu nutzen, um sowohl Datenverbindung als auch Strom für Geräte wie W-LAN, IP- und Sicherheitskamera, VoIP-Telefon, Computer und andere bereitzustellen. Der Überspannungsableiter TP302 wurde entwickelt, um PSE (Stromversorgungsgeräte), die an ein Netzwerk angeschlossen sind, vor transienten Überspannungen zu schützen. Der Ethernet-Überspannungsschutz PoE unterstützt sowohl \u003cstrong\u003eMode A (Pins 1,2+ 3,6-)\u003c\/strong\u003e als auch \u003cstrong\u003eB (7,8+ 4,5-)\u003c\/strong\u003e des Standards \u003cstrong\u003e802.3af\u003c\/strong\u003e zur Versorgung mit Gleichstrom. \u003cstrong\u003e802.3af (PoE)\u003c\/strong\u003e kann bis zu 30 Watt über das Netzwerkkabel abgeben, wobei 25,5 Watt für Geräte zur Verfügung stehen. Aus diesem Grund wird PoE Plus auch als High PoE bezeichnet. Der Ethernet-Schutz ermöglicht die PoE-Benetzung in das LAN-Kabel mit einer Spannung von bis zu 60 Volt DC, wobei typischerweise 48 VDC verwendet werden.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003eDer Ethernet-Blitzableiter muss ordnungsgemäß geerdet sein, damit er funktioniert. Der \u003cstrong\u003eEthernet-Masseleiter\u003c\/strong\u003e (11 Zoll - 16 AWG) am Überspannungsschutz muss auf dem kürzesten Weg mit der Erde verbunden werden. Überschüssiger Strom folgt dem Weg mit dem geringsten Widerstand. In den meisten Fällen ist eine Erdungssammelschiene an einem Schaltschrank oder einem Netzwerkschrank bereits geerdet und ist in der Regel die einfachste Art, den Draht zu erden. Weitere Optionen für den Erdungsüberspannungsschutz RJ45 ist der Erdungsblock an der Schalttafel, der Erdungsstab oder die Klemme der nächstgelegenen Steckdose, die mit dem Erdungskabel mit dem kreisförmigen Erdungsloch an der mittleren Schraube des geerdeten Auslasses verbunden wird.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDer Montageflansch\u003c\/strong\u003e auf beiden Seiten des Blitzschutzes ermöglicht eine einfache Montage an einer Wand, einem Netzwerk-Paneel, -Schrank oder -Rack, der mit Schrauben befestigt wird (nicht im Lieferumfang enthalten).\u003c\/p\u003e\n\u003cp\u003eDer Blitzableiter kann mit einem ungeschirmten Twisted Pair (UTP) oder geschirmten (STP) Kabeln verwendet werden. Der Ableiter ist in einem Aluminiumgussgehäuse untergebracht. Das Metallgehäuse ermöglicht es, abgeschirmten Strom durch das Metallgehäuse des Überspannungsschutzes zu leiten.\u003c\/p\u003e\n\u003cp\u003eDer Line-to-Line (Linie zu Linie) Ethernet-Überspannungsschutzmodus schützt vor Kurzschlüssen zwischen verschiedenen Netzwerkknoten, während der Line-to-Ground-Modus (Linie zu Boden) vor Kurzschlüssen zwischen dem Netzwerkknoten und der Erde schützt. Da nicht bekannt ist, wo die Transiente stattfinden wird, sorgt der Schutz beider Modi dafür, dass Schäden minimiert werden. Der Nennableitstrom von 5KA definiert den Spitzenwert des Stroms, der durch den SPD mit einer Wellenform von 8\/20μs Mikrosekunden geleitet werden kann, wobei der RJ45-Blitzableiter nach 15 Überspannungen funktionsfähig bleibt.\u003c\/p\u003e\n\u003cp\u003eSobald die Ethernet-Spannung des Überspannungsschutzgerätes seine vorgesehene Größe überschreitet, beginnt er zu \"klemmen\" und leitet die Energie direkt an das elektrische Erdungssystem. Eine bidirektionale Klemmung des CAT5 Überspannungsschutzes ermöglicht das Über- und Unterschreiten der Referenzspannung durch Klemmen der Spannung, das Schäden verursachen kann.\u003c\/p\u003e\n\u003cp\u003eDer Überspannungsschutz des Ethernet-Netzwerks funktioniert in beide Richtungen (IN\/OUT), sodass das Signalkabel des Quelleingangs von jeder Seite aus angeschlossen werden kann. Es ist nicht wichtig, auf welcher Seite sich das Gerät befindet, aber der Überspannungsschutz schützt Netzwerkgeräte nur auf der gegenüberliegenden Seite, auf der die Überspannung auftritt. Um Geräte auf beiden Seiten zu schützen, wird empfohlen, einen der Überspannungsableiter an jedem Ende des RJ45-Kabels in der Netzwerktopologie zu verwenden.\u003c\/p\u003e\n\u003cp\u003eDie Investition in einen kleinen, einfach zu installierenden Überspannungsschutz mit allen erforderlichen Funktionen und bewährter Zuverlässigkeit kann die sicherste und kostengünstigste Lösung zum Schutz Ihres gesamten Ethernet-Netzwerks sein.\u003c\/p\u003e\n\u003cp\u003eNennableitstrom (8\/20μs): 5 KA\u003cbr\u003ePoE-Nennspannung: \u0026lt;60V\u003cbr\u003ePoE-Strom bis zu \u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003e1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003c\/span\u003e\u003cbr\u003ePoE-Modus Unterstützungsmodus A und B für Leistung Impedanz 100 Ohm\u003cbr\u003eGeprüfte Normen IEC 61643-21, IEC61000-4-5\u003cbr\u003eKlemmspannung Leitung - Masse: 72 Volt\u003cbr\u003eKlemmspannung Netzleitung: 72 Volt\u003cbr\u003eLinie-Linie, Linie-Boden\u003cbr\u003eBetriebstemperatur -40°C (-40°F) bis +80°C (+176°F)\u003cbr\u003eAußenabmessungen (B*L*H) 26*26*70 mm\u003cbr\u003eGewicht: 60 g\u003c\/p\u003e\n\u003ch6\u003e\u003cimg title=\"Spanish\" height=\"30px\" width=\"30px\" src=\"https:\/\/www.worldoftales.com\/media\/flags\/Spain3.png\"\u003e\u003c\/h6\u003e\n\u003cp\u003eEl \u003cstrong\u003eprotector de sobretensiones para Ethernet\u003c\/strong\u003e es un dispositivo de protección contra sobretensiones (SPD) que se inserta en línea en un cable RJ45 CAT6\/CAT5\/CAT5e para evitar daños en los equipos electrónicos conectados en las redes.\u003c\/p\u003e\n\u003cp\u003eLas potentes sobrecargas contra las que este dispositivo protege incluyen descargas directas de rayos, picos de voltaje o sobretensiones PoE. Además de la protección primaria (un golpe directo en una línea), el supresor de rayos también ofrece una protección secundaria, que detiene las sobretensiones inducidas por CEM (descarga de rayo cercana a Ethernet).\u003c\/p\u003e\n\u003cp\u003e[El Protector contra sobretensiones para Ethernet modelo TP302 ofrece protección multietapa, utilizando un \u003cstrong\u003eTubo de Descarga de Gas\u003c\/strong\u003e (GDT) en 4 pares (8 cables), descargadores de chispas, resistencias en serie de limitación de corriente y un conjunto de diodos de baja capacitancia en la etapa final.]\u003c\/p\u003e\n\u003cp\u003eLos \u003cstrong\u003eTubos de Descarga de Gas (GDT)\u003c\/strong\u003e se han desarrollado para superar algunas de las desventajas de los protectores basados en diodos, como la capacidad de gestión de energía y son adecuados para casi todas las sobrecargas, ya sean de alta o baja frecuencia. Las sobrecargas pueden ser interceptadas por un supresor de rayos de Tubo de Descarga de Gas, proporcionando un riguroso rendimiento de control de descarga de chispa. El supresor contra sobretensiones Ethernet TP302 usa un Tubo de Descarga de Gas (GDT) en los 4 pares (8 cables). Los Tubos de Descarga de Gas disipan el voltaje transitorio a través de un gas plasma contenido que aprovecha el exceso de voltaje en la energía entrante y lo libera de manera segura. Esto garantiza la seguridad en una amplia gama de costosos componentes, como conmutadores, enrutadores, módems, puentes, repetidores o cualquier parte de la red de servicios de Internet.\u003c\/p\u003e\n\u003cp\u003eLa tasa de transferencia de datos del protector contra sobretensiones \u003cstrong\u003eGigabit 10\/100\/1000 (GbE)\u003c\/strong\u003e soporta una velocidad de datos máxima ultra rápida de 1 Gigabit por segundo (Gbps - 1000 Mbps) y no afecta al rendimiento de velocidad en la red de área local.\u003c\/p\u003e\n\u003cp\u003eEl \u003cstrong\u003eprotector contra sobretensiones PoE\u003c\/strong\u003e permite que un solo cable RJ-45 proporcione tanto conexión de datos como energía eléctrica a un dispositivo tales como un punto de acceso inalámbrico, un IP y cámara de seguridad, teléfono VoIP, ordenador y otros. El supresor de sobretensiones TP302 está diseñado para proteger los PSE (equipos de alimentación) conectados a una red de sobretensiones transitorias. El protector contra sobrecarga de Ethernet PoE es compatible con el \u003cstrong\u003eModo A (pines 1,2+ 3,6-) y B (7,8+ 4,5-)\u003c\/strong\u003e del estándar \u003cstrong\u003e802.3af\u003c\/strong\u003e para suministrar alimentación de CC. El estándar \u003cstrong\u003e802.3af (PoE)\u003c\/strong\u003e puede suministrar hasta 15.4 vatios por puerto a través de cables Cat 5 con 12,95 vatios que estarán disponibles con seguridad en el dispositivo alimentado, mientras que \u003cstrong\u003e802.3bt (PoE +)\u003c\/strong\u003e puede suministrar hasta 30 vatios a través de cables de red con 25,5 vatios disponibles para dispositivos. Por esta razón el PoE Plus también se conoce como \u003cstrong\u003eHigh PoE\u003c\/strong\u003e. El protector Ethernet permite que se introduzca Poe en el cable LAN a un voltaje de hasta 60 voltios de CC, y normalmente se usan 48 VCC.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003eEl protector contra rayos de Ethernet debe estar correctamente conectado a tierra para funcionar. El \u003cstrong\u003ecable de tierra\u003c\/strong\u003e Ethernet (27,94 centímetros - 16 AWG) del protector contra sobrecargas debe conectarse a tierra a través del camino más corto. El exceso de electricidad seguirá el camino de menor resistencia. En la mayoría de los casos, una barra de conexión a tierra en un panel eléctrico o en un armario de red rack ya están conectados a tierra y, por lo general, es la forma más fácil de conectar el cable a tierra. Otras opciones para poner a tierra el protector de sobrevoltaje RJ45 son el bloque de conexión a tierra en el panel del interruptor, la varilla de conexión a tierra o en el terminal de corriente con toma de tierra más cercano conectando el cable de tierra al orificio circular de conexión a tierra en el tornillo central de toma de tierra.\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eLa \u003cstrong\u003ebrida de montaje\u003c\/strong\u003e en ambos lados del supresor de sobretensiones permite un fácil montaje en la pared, al panel de red, al armario rack o bastidor mediante tornillos (no incluidos).\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003eEl pararrayos se puede usar con cables tipo Par Trenzado sin Blindaje (UTP) o Blindados (STP). El protector contra sobretensiones está inserto en una carcasa de \u003cstrong\u003ealuminio fundido\u003c\/strong\u003e. La carcasa metálica permite que la corriente \u003cstrong\u003eblindada\u003c\/strong\u003e pase a través de la carcasa metálica del protector contra sobretensiones de la red.\u003c\/p\u003e\n\u003cp\u003eEl modo de protección contra sobretensiones de Ethernet \u003cstrong\u003eLinea-a-Linea\u003c\/strong\u003e ayuda a proteger contra cortocircuitos entre diferentes nodos del sistema de red, mientras que el modo de \u003cstrong\u003eLínea-a-Tierra\u003c\/strong\u003e protege contra cortocircuitos entre el nodo de red y la tierra. Como no se sabe dónde ocurrirá lo transitorio, tener ambos modos protegidos garantiza que el daño se minimice. La corriente de descarga nominal de \u003cstrong\u003e5KA\u003c\/strong\u003e define el valor máximo de corriente que puede pasar a través del SPD teniendo forma de onda de 8\/20 μs microsegundos donde el protector contra rayos RJ45 sigue funcionando después de 15 picos de tensión.\u003c\/p\u003e\n\u003cp\u003eUna vez que el voltaje de Ethernet del protector contra sobretensiones excede su grado diseñado, \"comienza a restringir\" y empieza a conducir energía directamente al sistema eléctrico de conexión a tierra. Una \u003cstrong\u003erestricción bidireccional\u003c\/strong\u003e en el protector contra sobretensiones CAT5 permite niveles por encima y por debajo del voltaje de referencia al bloquear el voltaje que puede causar daños.\u003c\/p\u003e\n\u003cp\u003eEl protector contra sobretensiones de red Ethernet funciona en ambas direcciones (IN \/ OUT), por lo que el cable de señal de entrada de la fuente se puede conectar a cualquier lado. No es importante de qué lado está el equipo, sin embargo, el protector contra sobrecargas protegerá el equipo de red solo en el lado opuesto al lugar donde ocurre la sobrecarga. Para proteger los dispositivos en ambos lados, se recomienda tener uno de los protectores contra sobrecargas en cada extremo del cable RJ45 en la topología de la red.\u003c\/p\u003e\n\u003cp\u003eInvertir en un protector contra sobretensiones pequeño y fácil de instalar con todas las características necesarias y una fiabilidad comprobada puede ser la solución más segura y económica para proteger toda su red Ethernet.\u003c\/p\u003e\n\u003cp\u003eCorriente de descarga nominal (8 \/ 20μs): 5 KA\u003cbr\u003eVoltaje PoE nominal: \u0026lt;60V\u003cbr\u003eCorriente PoE hasta \u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003e1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003c\/span\u003e\u003cbr\u003eModo PoE admite el Modo A y B para suministro de alimentación\u003cbr\u003eImpedancia de 100 ohmios\u003cbr\u003eNormas probadas IEC 61643-21, IEC61000-4-5\u003cbr\u003eVoltaje de restricción Línea-a-Tierra: 72 voltios\u003cbr\u003eVoltaje de restricción Línea-a-Línea: 72 Voltios\u003cbr\u003eModos de protección Línea-a-Línea, Línea-a-Tierra\u003cbr\u003eTemperatura de funcionamiento -40 ° C (-40 ° F) a + 80 ° C (+ 176 ° F)\u003cbr\u003eDimensiones exteriores (A * L * Al) 26 * 26 * 70 mm\u003cbr\u003ePeso: 60 g\u003c\/p\u003e\n\u003ch6\u003e\u003cimg title=\"Japanese\" height=\"30px\" width=\"30px\" src=\"https:\/\/www.worldoftales.com\/media\/flags\/Japan3.png\"\u003e\u003c\/h6\u003e\n\u003cp\u003eイーサネットサージプロテクタは、電子ネットワーク機器の損傷を予防するために、RJ45\/ CAT6\/CAT5\/CAケーブルにインラインされているサージ保護機器(SPD)です。\u003c\/p\u003e\n\u003cp\u003e直撃雷、電圧ノイズ、PoE過電圧など強力なサージから保護してくれるデバイスです。一次保護(ラインへの直撃)に併せて、避雷器による二次保護を設けることで、EMFによって引き起こされたサージ(近場の落雷イーサネット)をキャッチすることが可能です。\u003c\/p\u003e\n\u003cp\u003eイーサネットサージプロテクタ　TP302は、全4ペア(8本のワイヤー)にガス放電管(GDT)を使って、スパークギャップ、電流制限直列抵抗、そして最後に低用量ダイオードアレイの多段階保護を提供致します。\u003c\/p\u003e\n\u003cp\u003eガス放電管 (GDT)は、エネルギー処理能力のようなダイオードベースの保護装置の欠点を克服するために開発され。高周波であれ低周波であれ、ほとんどすべてのサージに適している厳密な火花放電制御性能を発揮します。イーサネットサージプロセッサTP302は、全4ペア(8本のワイヤー)にガス放電管 (GDT)を使用しています。ガス放電管は、入ってくる電力の過剰な電圧を利用し、封じ込められたプラズマガスを通して過渡電圧を消散させます。スイッチ、ルーター、モデム、ブリッジ、リピーター、インターネットサービスネットワークのあらゆる部分などの安全を保障します。\u003c\/p\u003e\n\u003cp\u003e避雷器の両側にフランジを取りつけることで、壁、ネットワークパネル、キャビネットもしくはラックに簡単にネジ(含まれていません)で取り付けることができます。\u003c\/p\u003e\n\u003cp\u003eギガビット10\/100\/1000 (GbE)転送の際のギガビットサージプロテクタのデータレートは、1ギガビット\/秒(Gbps - 1000 Mbps)の超高速最大データレートをサポートし、ローカルエリアネットワークの高速パフォーマンスには影響しません。\u003c\/p\u003e\n\u003cp\u003ePOEサージプロテクタは、1本のRJ-45ケーブルで、ワイヤレスアクセスポイント、IPおよび防犯カメラ、VoIP電話、コンピューターなどの機器にデータ接続と電力の両方を提供することを可能にします。サージアレスタTP302は、ネットワークに接続されているPSE(電源装置)を過渡電圧から保護するよう設計されています。イーサネットサージプロテクタPoEは、DC電源を供給するための802.3af (PoE)規格Aモード (Pins 1,2+ 3,6-) および B (7,8+ 4,5-)の両方をサポートします。802.3af (PoE)は、Cat5ケーブルを介してポートあたり最大15.4Wを12.95Wで供給可能であり、一方、802.3bt (PoE++)はネットワークケーブルを介して最大30Wを25.5Wで装置に供給可能です。そのため、PoE PlusはHigh PoEとも呼ばれています。イーサネットプロテクタは最大60DCの電圧でLANケーブルに注入されるPoEを許容し、通常48VDCが使用されます。\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003eイーサネット避雷器は、正しく機能するよう接地されている必要があります。サージプロテクタのイーサネットアースワイヤー(11インチ-16AWG)は、最短経路でアースに接続する必要があります。過剰な電気は、最も抵抗の少ない経路をたどります。ほとんどの場合、電気パネルまたはネットワークラックキャビネットのアースデバイスはすでにアースされており、通常はワイヤーをアースする最も簡単な方法です。RJ45サージプロテクタを接地するその他の方法は、接地線を接地されているコンセントの中心ネジの形の接地穴に接続して、ブレーカーパネルのアースブロック、アース棒、または最も近いコンセントの端子です。\u003c\/p\u003e\n\u003cp\u003e避雷器は、シールドなしツイストペア(UTP)ケーブルまたはシールド付き(STP)ケーブルで使用できます。避雷器は鋳造アルミの筐体に収容されています。金属製ハウジングにより、シールド電流をネットワークサージプロテクタの金属製ケースに流すことができます。\u003c\/p\u003e\n\u003cp\u003eLine-to-Lineイーサネットサージ保護モードは、ネットワークシステムの異なるノード間の短絡から保護するのに役立ちますが、\u003c\/p\u003e\n\u003cp\u003eLine-to-Grounモードは、ネットワークノードとアース間の短絡から保護します。どこで過渡現象が発生するのかはわからないので、両方のモードを保護することで損傷を最小限に抑えることができます。5KAの公称放電電流は、RJ45避雷器が15回のサージ後も機能し続ける8 \/20μsマイクロ秒の波形を持つSPDを通過することができる電流のピーク値を定義します。\u003c\/p\u003e\n\u003cp\u003eサージプロテクタのイーサネット電圧が設計された定格を超えると、「クランプ」を開始し、電気接地システムに直接エネルギーを伝導し始めます。 CAT5サージプロテクタの双方向クランプは、損傷を引き起こす可能性のある電圧をクランプすることによって基準電圧の上下のレベルを許容します。\u003c\/p\u003e\n\u003cp\u003eイーサネットネットワークサージプロテクタは、双方向（IN \/ OUT）で動作するため、ソース入力信号ケーブルはどちら側にも接続できます。機器の裏側は重要ではありませんが、サージプロテクタはネットワーキング機器を保護するのは、サージが発生する場所の反対側だけです。両側でデバイスを保護するために、ネットワークトポロジ内のRJ45ケーブルの両端にそれぞれ1つずつサージプロテクタを配置することをお勧めします。\u003c\/p\u003e\n\u003cp\u003e公称放電電流（8 \/20μs）：5KA\u003cbr\u003e公称PoE電圧: \u0026lt;60V\u003cbr\u003e最大1AのPoE電流\u003cbr\u003e電力用PoEモード サポートモードAおよびB\u003cbr\u003eインピーダンス100オーム\u003cbr\u003e検証済み標準IEC 61643-21, IEC61000-4-5\u003cbr\u003eクランプ電圧ライン-グラウンド: 72ボルト\u003cbr\u003eクランプ電圧ライン-ライン: 72ボルト\u003cbr\u003e保護モードライン-ライン、ライン-グラウンド\u003cbr\u003e動作温度-40°C (-40°F) から +80°C (+176°F)\u003cbr\u003e外形寸法(広さ*長さ*高さ) 26*26*70 mm\u003c\/p\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":17896739045443,"sku":"302","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/9-2.png?v=1766189408"},{"product_id":"outdoor-ethernet-surge-protector","title":"Outdoor Ethernet Thunder Lightning Surge Protector for PoE+ Gigabit 1000Mbs - LAN Network","description":"\u003ch4\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B008060BU0\/\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: 741360887831\u003c\/strong\u003e\u003cbr\u003e\u003cem\u003eModel Number: TP303\u003c\/em\u003e\u003cbr\u003e\n\u003c\/h4\u003e\n\u003cp\u003e\u003cstrong\u003eOutdoor Ethernet Surge Protector\u003c\/strong\u003e is a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment. It can be mounted outside, and it's resistant to weather conditions (weatherproof IP44). It comes in the box enclosure which can be secured with a lock (not included).\u003cbr\u003e\u003cbr\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eGas discharge tubes (GDTs)\u003c\/strong\u003e are developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrestor so it provides a rigorous spark discharge control performance.\u003cbr\u003e\u003cbr\u003eEthernet Surge Suppressor TP303 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as switch, router, modem, bridge, repeater, or any part of internet service network.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eMounting holes\u003c\/strong\u003e allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003cul class=\"a-vertical a-spacing-none\"\u003e\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000 (GbE) and High PoE+ Networks\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe gigabit surge protector date rate of Gigabit 10\/100\/1000 (GbE) transfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network. POE Surge Protector allows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP303 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The lightning protector PoE supports both Mode A (Pins 1,2+ 3,6-) and B (7,8+ 4,5-) of the 802.3af standard. 802.3af (PoE) can deliver up to 15.4 watts per port with 12.95W at the powered device, while 802.3at (PoE+) can deliver up to 30 watts with 25.5 watts available to devices. PoE Plus is also known as High PoE.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/7dFXvaW61LE\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet ground wire (11 Inch - 12 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw. The lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProtection Modes Line-Line, Line-Ground\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Line-to-Line ethernet surge protection mode helps protect against short circuits between different nodes of the network system while the Line-to-Ground mode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of 5KA defines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003cbr\u003e\u003cbr\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A bidirectional clamping on CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003cbr\u003e\u003cem\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eMultidirectional\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMaximum Discharge Current (8\/20μs): 10 KA\u003c\/li\u003e\n\u003cli\u003eNominal PoE voltage : \u0026lt;60V\u003c\/li\u003e\n\u003cli\u003ePoE current up to 2A\u003c\/li\u003e\n\u003cli\u003ePoE Mode Support Mode A and B for Power\u003c\/li\u003e\n\u003cli\u003eProtection Modes Line-Line, Line-Ground\u003c\/li\u003e\n\u003cli\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/li\u003e\n\u003cli\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/li\u003e\n\u003cli\u003eClamping Voltage Line-Line: 72 Volts\u003c\/li\u003e\n\u003cli\u003eImpedance 100 ohms\u003c\/li\u003e\n\u003cli\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/li\u003e\n\u003cli\u003eOutside Dimensions (W*L*H) 78*103*49 mm\u003c\/li\u003e\n\u003cli\u003eWeight: 110 g\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInvesting in a small, easy to install surge protector with all of the needed features and proven reliability can be the safest and most cost-effective solution for protecting your whole Ethernet network.\u003c\/p\u003e\n\u003ch4\u003e\u003cbr\u003e\u003c\/h4\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":17896776237123,"sku":"303","price":39.98,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/6a3671aa691ae6bb7f2ff7485cfc99bd.jpg?v=1551798084"},{"product_id":"din-ethernet-surge-protector","title":"Ethernet Surge Protector - PoE+ - Gigabit - (with DIN Rail Mount Option)","description":"\u003ch1\u003e\n\u003ca href=\"https:\/\/www.amazon.com\/dp\/B078NKGPJC\/\"\u003e\u003cstrong\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/strong\u003e\u003c\/a\u003e\u003cbr\u003e\u003cstrong\u003eEthernet Surge Protector \u003c\/strong\u003e\n\u003c\/h1\u003e\n\u003cp\u003e\u003cstrong\u003eUPC: 638362929471\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP309\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eAn \u003cstrong\u003eEthernet Surge Protector\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eis a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment. It can be mounted on the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eDIN Rail\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eor used\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003estandalone\u003c\/span\u003e.\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eGas discharge tubes (GDTs)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eare developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrester so it provides a rigorous spark discharge control performance.\u003c\/p\u003e\n\u003cp\u003eEthernet Surge Suppressor TP309 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as switch, router, modem, bridge, repeater, or any part of internet service network.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/invS-NoRYSY\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000 (GbE) and High PoE+ Networks\u003c\/h3\u003e\n\u003cp\u003eThe gigabit surge protector date rate of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eGigabit 10\/100\/1000 (GbE)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003etransfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ePOE Surge Protector\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eallows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP303 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The lightning protector PoE supports both\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eMode\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eA (Pins 1,2+ 3,6-) and B\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(7,8+ 4,5-)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eof the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003estandard.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af (PoE)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 15.4 watts per port with 12.95W at the powered device, while\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3at (PoE+)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 30 watts with 25.5 watts available to devices. PoE Plus is also known as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eHigh PoE\u003c\/span\u003e.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. When used on the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eDIN Rail\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eit is connected to the ground through the rail, and when used as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003estandalone a ground wire\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eneeds to be connected from the surge protector to the ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/p\u003e\n\u003cp\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Line\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eethernet surge protection mode helps protect against short circuits between different nodes of the network system while the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Ground\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003emode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e5KA\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003edefines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/p\u003e\n\u003cp\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ebidirectional clamping\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eSpecifications\u003c\/h3\u003e\n\u003ch4 class=\"a-spacing-mini a-color-secondary a-text-italic\"\u003eMultidirectional\u003c\/h4\u003e\n\u003cp class=\"a-spacing-base\"\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul class=\"a-unordered-list a-vertical\"\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eNominal Discharge Current (8\/20μs): 5 KA\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eNominal PoE voltage : \u0026lt;60V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePoE current up to 1.2A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePoE Mode Support Mode A and B for Power\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eClamping Voltage Line-Line: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eResponse time \u0026lt; 100 ns\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eOutside Dimensions (W*L*H) 26*26*68 mm\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePlastic Case\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eWeight: 35 g\u003c\/span\u003e\u003c\/span\u003e \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOur \u003ca title=\"ethernet surge protector (pack of 2)\" href=\"https:\/\/www.tupavco.com\/products\/din-rail-ethernet-surge-protector-2-pack\"\u003eEthernet Surge Protector (Pack of 2)\u003c\/a\u003e or \u003ca title=\"ethernet surge protector (pack of 10)\" href=\"https:\/\/www.tupavco.com\/products\/din-rail-ethernet-surge-protector-10-pack\"\u003eEthernet Surge Protector (Pack of 10)\u003c\/a\u003e may be useful for you if you're looking for multiple protectors. \u003c\/p\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":17921821016131,"sku":"309","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/TP_309_2.png?v=1565805077"},{"product_id":"network-rack-ethernet-surge-protector","title":"Rack Mount Rail Panel 19\" with 16x DIN Ethernet Surge Protectors GbE PoE+ Gigabit 1000Mbs","description":"\u003cp\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B078PDRW12\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cstrong\u003eUPC: 638362929488\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP316\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cmeta charset=\"utf-8\"\u003e \u003cspan\u003eAssembly required (16 screws included); Clips included only for DIN mount;\u003c\/span\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003eRack Mount Rail 1U with 16x Ethernet Surge Protectors protects 16 lines, and it's ready to mount into rackmount slot on 19\" (inch) (1U) data protection rack server cabinet panel.\u003c\/p\u003e\n\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003eEach Ethernet Surge Protector is a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment. Each single protector on the rail can be replaced with single compatible Tupavco item TP309 (ASIN: B078NKGPJC).\u003cbr\u003e\u003cbr\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003cbr\u003e\u003cbr\u003eGas discharge tubes (GDTs) are developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrester so it provides a rigorous spark discharge control performance.\u003cbr\u003e\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/p-c37iA_EbQ\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003eEthernet Surge Suppressor TP316 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as switch, router, modem, bridge, repeater, or any part of internet service network.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e16 Lines\/Ports RJ45 Lightning Protection for Gigabit 10\/100\/1000 (GbE) and High PoE+ Networks\u003c\/strong\u003e\u003cbr\u003e\u003cbr\u003eThe gigabit surge protector date rate of Gigabit 10\/100\/1000 (GbE) transfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network. POE Surge Protector allows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP303 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The lightning protector PoE supports both Mode A (Pins 1,2+ 3,6-) and B (7,8+ 4,5-) of the 802.3af standard. 802.3af (PoE) can deliver up to 15.4 watts per port with 12.95W at the powered device, while 802.3at (PoE+) can deliver up to 30 watts with 25.5 watts available to devices. PoE Plus is also known as High PoE.\u003c\/p\u003e\n\u003ch3\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eThe rackmount must be properly grounded to work through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel or grounding rod.\u003cbr\u003e\u003cbr\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables.\u003c\/p\u003e\n\u003ch3\u003eProtection Modes Line-Line, Line-Ground\u003c\/h3\u003e\n\u003cp\u003eThe Line-to-Line ethernet surge protection mode helps protect against short circuits between different nodes of the network system while the Line-to-Ground mode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of 5KA defines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003cbr\u003e\u003cbr\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A bidirectional clamping on CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003ch3\u003e\n\u003cbr\u003e\u003cb\u003eProtector Data\u003c\/b\u003e\n\u003c\/h3\u003e\n\u003cp\u003e- 100\/1000 MbPS \u003cbr\u003e- DIN 3 rail mountable or configure in the 1U rack cabinet chassis \u003cbr\u003e- Protects all 4 pairs by UL rated differential gas discharge tube (GDT) \u003cbr\u003e- IEEE 802.3 af\/at (Transmission) Mode A \u0026amp; B\u003cbr\u003e- Support normal and reverse PoE power polarity\u003cbr\u003e- IEC 61000-4-5 (Lightning\/Surge) 20KA(8\/20µs) \u003cbr\u003e- Nominal PoE voltage \u0026lt; 60V\u003cbr\u003e- Shunt Capacitance \u0026lt; 2 pF \u003cbr\u003e- Impedance 100 ohms \u003cbr\u003e- Line and protected equipment bidirectional protection \u003cbr\u003e- Shielded\/Grounded RJ-45 jacks for line and protected equipment \u003cbr\u003e- Non-Metallic UL94V0 flame rating enclosure \u003cbr\u003e- IEC 61643-21, IEC61000-4-5, CORE 1089 compliant \u003cbr\u003e- RoHS compliant \u003cbr\u003e- REACH compliant\u003cbr\u003e\u003cbr\u003eClamping Voltage (Pin1-2,3-6,4-5,7-8) \u003cbr\u003eLine-Line: 72 Volts\u003cbr\u003eLine-Ground: 72 Volts\u003cbr\u003e\u003cbr\u003eNominal PoE Voltage \u0026lt;60 V\u003cbr\u003eMaximum continuous current 1.2 A\u003cbr\u003eResponse time (Line-Line, Line-Ground) \u0026lt; 100 ns\u003cbr\u003eMaximum Surge Current (8\/20?s) per IEC 61000-4-5 5 KA\u003cbr\u003eShunt Capacitance \u0026lt; 1 pF\u003cbr\u003eStandard Connectors Shielded RJ-45 Jacks * 2\u003cbr\u003ePoE Mode Support Mode A and B for Power\u003cbr\u003eEnclosure Material Non-Metallic UL94V0 flame rating\u003cbr\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003cbr\u003e\u003cbr\u003e\u003cb\u003e\u003c\/b\u003eDIN Rail 19\" (1U) protection rack panel data\u003cbr\u003e- Holds up to 16 protection units (GbE-GUARD CSD, included)\u003cbr\u003e- Chassis Material Aluminum\u003cbr\u003e- Ground wire 8-inch AWG-9\u003cbr\u003e- Outside Dimensions (W*L*H) 44 x 482.6 x 25 mm\u003c\/p\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":17998285897795,"sku":"316","price":399.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/TP_316_1.png?v=1565871128"},{"product_id":"ethernet-surge-protector-2-pack","title":"Tupavco TP302 Ethernet Surge Protector PoE++ Gigabit RJ45 Lightning Suppressor (2 Pack)","description":"\u003ch4\u003e\n\u003ca href=\"https:\/\/www.amazon.com\/dp\/B07GBLFFNK\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\" alt=\"\"\u003e\u003c\/a\u003e\u003cbr\u003e\u003cstrong\u003eUPC: 638362929709\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP302x2\u003c\/em\u003e\n\u003c\/h4\u003e\n\u003cp\u003e\u003cstrong\u003e2 Pack (Pair)\u003c\/strong\u003e of Ethernet Surge Protector TP302\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eEthernet Surge Protector\u003c\/b\u003e\u003cspan\u003e is a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning).\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eEthernet Surge Suppressor TP302 use a \u003c\/span\u003e\u003cb\u003eGas Discharge Tube\u003c\/b\u003e\u003cspan\u003e (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as network hub, switch, router, modem, bridge, repeater, or any part of ISP (internet service provider) network or LAN system.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePOE Surge Protector\u003c\/b\u003e\u003cspan\u003e allows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP302 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The ethernet surge protector PoE supports both \u003c\/span\u003e\u003cb\u003eMode\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e\u003cb\u003eA (Pins 1,2+ 3,6-) and B\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e\u003cb\u003e(7,8+ 4,5-)\u003c\/b\u003e\u003cspan\u003e of the \u003c\/span\u003e\u003cb\u003e802.3af\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e\u003cspan\u003estandard for supplying DC power. \u003c\/span\u003e\u003cb\u003e802.3af (PoE)\u003c\/b\u003e\u003cspan\u003e can deliver up to 15.4 watts per port over Cat5 cables with 12.95W assured to be available at the powered device, while \u003c\/span\u003e\u003cb\u003e802.3bt (PoE++)\u003c\/b\u003e\u003cspan\u003e can deliver up to 30 watts over network cables with 25.5 watts available to devices. For that reason, PoE Plus is also known as \u003c\/span\u003e\u003cb\u003eHigh PoE\u003c\/b\u003e\u003cspan\u003e. Ethernet surge protector allows PoE injected into the LAN cable at a voltage up to 60 volts DC, and typically 48 VDC is used.\u003c\/span\u003e\u003c\/p\u003e\n\u003cdiv data-cel-widget=\"aplus-launchpad-brand-description-left\" class=\"celwidget aplus-module launchpad-brand-description-left\"\u003e\n\u003cdiv class=\"a-section a-spacing-top-mini launchpad-module launchpad-module-brand-description-left\"\u003e\n\u003cdiv class=\"a-section launchpad-text-left-justify\"\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eMounting flange\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon the both sides of lightning suppressor allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cspan\u003eThe unit’s data rate\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan\u003eof \u003c\/span\u003e\u003cb\u003eGigabit 10\/100\/1000 (GbE)\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e\u003cspan\u003etransfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet \u003c\/span\u003e\u003cb\u003eground wire\u003c\/b\u003e\u003cspan\u003e (12 Inch - 16 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e\u003cspan\u003e\u003c\/span\u003e\u003c\/i\u003e\u003cspan\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables. The arrester is housed in a \u003c\/span\u003e\u003cb\u003ecast aluminum\u003c\/b\u003e\u003cspan\u003e enclosure. The metal housing allows \u003c\/span\u003e\u003cb\u003eshielded\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e\u003cspan\u003ecurrent to be passed through the metal case of the network surge protector.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe \u003c\/span\u003e\u003cb\u003eLine-to-Line\u003c\/b\u003e\u003cspan\u003e ethernet surge protection mode helps protect against short circuits between different nodes of the network system while the \u003c\/span\u003e\u003cb\u003eLine-to-Ground\u003c\/b\u003e\u003cspan\u003e mode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of \u003cstrong\u003e20\u003c\/strong\u003e\u003c\/span\u003e\u003cb\u003eKA\u003c\/b\u003e\u003cspan\u003e defines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eOnce the surge voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A \u003c\/span\u003e\u003cb\u003ebidirectional clamping\u003c\/b\u003e\u003cspan\u003e on CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eNetwork surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cp\u003eInvesting in a small, easy to install surge protector with all of the needed features and proven reliability can be the safest and most cost-effective solution for protecting your whole Ethernet network.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eNominal Discharge Current (8\/20μs):  20 KA\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eNominal PoE voltage : \u0026lt;60V\u003cbr\u003e\u003c\/span\u003ePoE current: 1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003cbr\u003e\u003cspan\u003ePoE Mode Support Mode A and B for Power\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eImpedance 100 ohms\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eTested standards IEC 61643-21, IEC61000-4-5\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eClamping Voltage Line-Ground: 72 Volts\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eClamping Voltage Line-Line: 72 Volts\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eProtection Modes Line-Line, Line-Ground\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eOutside Dimensions (W*L*H) 26*26*70 mm\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eWeight: 60 g\u003c\/span\u003e\u003c\/p\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":19473426939971,"sku":"302x2","price":60.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/302x2.png?v=1668470882"},{"product_id":"ethernet-surge-protector-10-pack","title":"Tupavco TP302 Ethernet Surge Protector PoE++ Gigabit RJ45 Lightning Suppressor (10 Pack)","description":"\u003ch4\u003e\n\u003ca href=\"https:\/\/www.amazon.com\/dp\/B07GBH3HF7\/\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003cbr\u003e\u003cb\u003e\u003cstrong\u003eUPC:\u003cspan\u003e 638362929686\u003c\/span\u003e\u003cbr\u003e\u003c\/strong\u003e\u003c\/b\u003e\u003cem\u003eModel Number: TP302x10\u003c\/em\u003e\n\u003c\/h4\u003e\n\u003cp\u003e\u003cstrong\u003e10 Pack\u003c\/strong\u003e of Ethernet Surge Protector TP302\u003cbr\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003eEthernet Surge Protector\u003c\/b\u003e\u003cspan\u003e is a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning).\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eEthernet Surge Suppressor TP302 use a \u003c\/span\u003e\u003cb\u003eGas Discharge Tube\u003c\/b\u003e\u003cspan\u003e (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as network hub, switch, router, modem, bridge, repeater, or any part of ISP (internet service provider) network or LAN system.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cb\u003ePOE Surge Protector\u003c\/b\u003e\u003cspan\u003e allows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP302 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The ethernet surge protector PoE supports both \u003c\/span\u003e\u003cb\u003eMode\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e\u003cb\u003eA (Pins 1,2+ 3,6-) and B\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e\u003cb\u003e(7,8+ 4,5-)\u003c\/b\u003e\u003cspan\u003e of the \u003c\/span\u003e\u003cb\u003e802.3af\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e\u003cspan\u003estandard for supplying DC power. \u003c\/span\u003e\u003cb\u003e802.3af (PoE)\u003c\/b\u003e\u003cspan\u003e can deliver up to 15.4 watts per port over Cat5 cables with 12.95W assured to be available at the powered device, while \u003c\/span\u003e\u003cb\u003e802.3bt (PoE++)\u003c\/b\u003e\u003cspan\u003e can deliver up to 30 watts over network cables with 25.5 watts available to devices. For that reason, PoE Plus is also known as \u003c\/span\u003e\u003cb\u003eHigh PoE\u003c\/b\u003e\u003cspan\u003e. Ethernet surge protector allows PoE injected into the LAN cable at a voltage up to 60 volts DC, and typically 48 VDC is used.\u003c\/span\u003e\u003cmeta charset=\"utf-8\"\u003e\u003c\/p\u003e\n\u003cdiv class=\"celwidget aplus-module launchpad-brand-description-left\" data-cel-widget=\"aplus-launchpad-brand-description-left\"\u003e\n\u003cdiv class=\"a-section a-spacing-top-mini launchpad-module launchpad-module-brand-description-left\"\u003e\n\u003cdiv class=\"a-section launchpad-text-left-justify\"\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eMounting flange\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon the both sides of lightning suppressor allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/qu_lFGQriyE\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cspan\u003eThe unit’s data rate\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan\u003eof \u003c\/span\u003e\u003cb\u003eGigabit 10\/100\/1000 (GbE)\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e\u003cspan\u003etransfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet \u003c\/span\u003e\u003cb\u003eground wire\u003c\/b\u003e\u003cspan\u003e (11 Inch - 16 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ci\u003e\u003cspan\u003e\u003c\/span\u003e\u003c\/i\u003e\u003cspan\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables. The arrester is housed in a \u003c\/span\u003e\u003cb\u003ecast aluminum\u003c\/b\u003e\u003cspan\u003e enclosure. The metal housing allows \u003c\/span\u003e\u003cb\u003eshielded\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e\u003cspan\u003ecurrent to be passed through the metal case of the network surge protector.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe \u003c\/span\u003e\u003cb\u003eLine-to-Line\u003c\/b\u003e\u003cspan\u003e ethernet surge protection mode helps protect against short circuits between different nodes of the network system while the \u003c\/span\u003e\u003cb\u003eLine-to-Ground\u003c\/b\u003e\u003cspan\u003e mode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of \u003cstrong\u003e20\u003c\/strong\u003e\u003c\/span\u003e\u003cb\u003eKA\u003c\/b\u003e\u003cspan\u003e defines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eOnce the surge voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A \u003c\/span\u003e\u003cb\u003ebidirectional clamping\u003c\/b\u003e\u003cspan\u003e on CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eNetwork surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cp\u003eInvesting in a small, easy to install surge protector with all of the needed features and proven reliability can be the safest and most cost-effective solution for protecting your whole Ethernet network.\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eNominal Discharge Current (8\/20μs):  20 KA\u003c\/span\u003e\u003cbr\u003e\u003cspan\u003eNominal PoE voltage : \u0026lt;60V\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003e\u003cmeta charset=\"utf-8\"\u003ePoE current: 1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003ePoE Mode Support Mode A and B for Power\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eImpedance 100 ohms\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eTested standards IEC 61643-21, IEC61000-4-5\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eClamping Voltage Line-Ground: 72 Volts\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eClamping Voltage Line-Line: 72 Volts\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eProtection Modes Line-Line, Line-Ground\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eOutside Dimensions (W*L*H) 26*26*70 mm\u003cbr\u003e\u003c\/span\u003e\u003cspan\u003eWeight: 60 g\u003c\/span\u003e\u003c\/p\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":19473456267331,"sku":"302x10","price":289.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/91F8KsuVoKL._SL1500.jpg?v=1561598389"},{"product_id":"din-rail-ethernet-surge-protector-10-pack","title":"Ethernet Surge Protector (10 pack) - PoE+ - Gigabit - (with DIN Rail Mount Option)","description":"\u003ch1\u003e\n\u003cstrong\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B08PXSD5KT\/\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cstrong\u003e\u003cmeta charset=\"utf-8\"\u003eEthernet Surge Protector (Pack of 10)\u003c\/strong\u003e\n\u003c\/h1\u003e\n\u003cp\u003e\u003cstrong\u003eUPC: 638362930033\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP309x10\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eAn \u003cstrong\u003eEthernet Surge Protector (Pack of 10)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eis a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment. It can be mounted on the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eDIN Rail\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eor used\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003estandalone\u003c\/span\u003e.\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eGas discharge tubes (GDTs)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eare developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrester so it provides a rigorous spark discharge control performance.\u003c\/p\u003e\n\u003cp\u003eEthernet Surge Suppressor TP309 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as switch, router, modem, bridge, repeater, or any part of internet service network.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/invS-NoRYSY\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000 (GbE) and High PoE+ Networks\u003c\/h3\u003e\n\u003cp\u003eThe gigabit surge protector date rate of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eGigabit 10\/100\/1000 (GbE)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003etransfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ePOE Surge Protector\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eallows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP303 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The lightning protector PoE supports both\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eMode\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eA (Pins 1,2+ 3,6-) and B\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(7,8+ 4,5-)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eof the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003estandard.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af (PoE)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 15.4 watts per port with 12.95W at the powered device, while\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3at (PoE+)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 30 watts with 25.5 watts available to devices. PoE Plus is also known as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eHigh PoE\u003c\/span\u003e.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. When used on the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eDIN Rail\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eit is connected to the ground through the rail, and when used as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003estandalone a ground wire\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eneeds to be connected from the surge protector to the ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/p\u003e\n\u003cp\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Line\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eethernet surge protection mode helps protect against short circuits between different nodes of the network system while the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Ground\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003emode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e5KA\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003edefines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/p\u003e\n\u003cp\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ebidirectional clamping\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eSpecifications\u003c\/h3\u003e\n\u003ch4 class=\"a-spacing-mini a-color-secondary a-text-italic\"\u003eMultidirectional\u003c\/h4\u003e\n\u003cp class=\"a-spacing-base\"\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul class=\"a-unordered-list a-vertical\"\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eNominal Discharge Current (8\/20μs): 5 KA\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eNominal PoE voltage : \u0026lt;60V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePoE current up to 1.2A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePoE Mode Support Mode A and B for Power\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eClamping Voltage Line-Line: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eResponse time \u0026lt; 100 ns\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eOutside Dimensions (W*L*H) 26*26*68 mm\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePlastic Case\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eWeight: 35 g\u003c\/span\u003e\u003c\/span\u003e \u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":37914049872068,"sku":"309x10","price":289.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/309x10.png?v=1765485856"},{"product_id":"din-rail-ethernet-surge-protector-2-pack","title":"Ethernet Surge Protector (2 pack) - PoE+ - Gigabit - (with DIN Rail Mount Option)","description":"\u003ch1\u003e\n\u003cstrong\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B08PXNN6JQ\/\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cstrong\u003e\u003cmeta charset=\"utf-8\"\u003eEthernet Surge Protector (Pack of 2)\u003cspan\u003e \u003c\/span\u003e\u003c\/strong\u003e\n\u003c\/h1\u003e\n\u003cp\u003e\u003cstrong\u003eUPC: 638362930026\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP309x2\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eAn \u003cstrong\u003eEthernet Surge Protector (Pack of 2)\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eis a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment. It can be mounted on the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eDIN Rail\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eor used\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003estandalone\u003c\/span\u003e.\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eGas discharge tubes (GDTs)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eare developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrester so it provides a rigorous spark discharge control performance.\u003c\/p\u003e\n\u003cp\u003eEthernet Surge Suppressor TP309 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as switch, router, modem, bridge, repeater, or any part of internet service network.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/invS-NoRYSY\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000 (GbE) and High PoE+ Networks\u003c\/h3\u003e\n\u003cp\u003eThe gigabit surge protector date rate of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eGigabit 10\/100\/1000 (GbE)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003etransfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ePOE Surge Protector\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eallows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP303 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The lightning protector PoE supports both\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eMode\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eA (Pins 1,2+ 3,6-) and B\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(7,8+ 4,5-)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eof the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003estandard.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af (PoE)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 15.4 watts per port with 12.95W at the powered device, while\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3at (PoE+)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 30 watts with 25.5 watts available to devices. PoE Plus is also known as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eHigh PoE\u003c\/span\u003e.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. When used on the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eDIN Rail\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eit is connected to the ground through the rail, and when used as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003estandalone a ground wire\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eneeds to be connected from the surge protector to the ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/p\u003e\n\u003cp\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Line\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eethernet surge protection mode helps protect against short circuits between different nodes of the network system while the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Ground\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003emode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e5KA\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003edefines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/p\u003e\n\u003cp\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ebidirectional clamping\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eSpecifications\u003c\/h3\u003e\n\u003ch4 class=\"a-spacing-mini a-color-secondary a-text-italic\"\u003eMultidirectional\u003c\/h4\u003e\n\u003cp class=\"a-spacing-base\"\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul class=\"a-unordered-list a-vertical\"\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eNominal Discharge Current (8\/20μs): 5 KA\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eNominal PoE voltage : \u0026lt;60V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePoE current up to 1.2A\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePoE Mode Support Mode A and B for Power\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eClamping Voltage Line-Line: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eResponse time \u0026lt; 100 ns\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eOutside Dimensions (W*L*H) 26*26*68 mm\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003ePlastic Case\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base a-color-secondary\"\u003eWeight: 35 g\u003c\/span\u003e\u003c\/span\u003e \u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":37914128023748,"sku":"309x2","price":60.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/33b5a06fe459d8e936e6c75a7bd30b8d.jpg?v=1615116021"},{"product_id":"tupavco-tp308-server-rack-rail-1u-19-front-mount-16-screw-slots-capacity-cold-rolled-steel-black-for-network-cabinet-and-electronics-media-devices","title":"Server Rack Rail 1U 19\" (Front Mount) 16 Screw Slots Capacity for Network Cabinet","description":"\u003cp\u003e\u003cstrong\u003eUPC: 638362929464\u003cbr\u003e\u003c\/strong\u003e\u003cem data-mce-fragment=\"1\"\u003eModel Number: TP308\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003eTP308 Rails were designed to fit any standard 19” server rack or computer networking media cabinet. They take up 1U (1RU) of rack space. Perfect for support of smaller networking devices (like ethernet surge protectors TP309) that need front access and has a screw mount option, without the need to mount them directly. 8-inch ground wire is attached. These rails are made from high-quality Cold Rolled Steel and Powder Coated finish and can hold up to 16 devices.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSupports holding up to 16 devices by screw on the rail\u003c\/li\u003e\n\u003cli\u003eFront mount on networking server racks and electronics media cabinets\u003c\/li\u003e\n\u003cli\u003eFits standard 1U 19 inch network cabinets; screw hole distance 1 inch\u003c\/li\u003e\n\u003cli\u003eCold Rolled Steel with Powder Coated finish (Black)\u003c\/li\u003e\n\u003cli\u003eIdeal for small networking devices with screw mount option for easy front access\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":37941132591300,"sku":"308","price":48.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/43eb00ad9475b0e2957b1bb9d537d00a.jpg?v=1611406891"},{"product_id":"outdoor-ethernet-thunder-lightning-surge-protector-for-poe-10-pack","title":"Outdoor Ethernet Thunder Lightning Surge Protector for PoE+ Gigabit 1000Mbs (10 Pack)","description":"\u003cp\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B0BV5VJDMY\/\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cstrong\u003eUPC: 850043852094\u003c\/strong\u003e\u003cbr\u003e\u003cem\u003eModel Number: TP303x10\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutdoor Ethernet Surge Protector\u003c\/strong\u003e is a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment. It can be mounted outside, and it's resistant to weather conditions (weatherproof IP44). It comes in the box enclosure which can be secured with a lock (not included).\u003cbr\u003e\u003cbr\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eGas discharge tubes (GDTs)\u003c\/strong\u003e are developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrestor so it provides a rigorous spark discharge control performance.\u003cbr\u003e\u003cbr\u003eEthernet Surge Suppressor TP303 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as switch, router, modem, bridge, repeater, or any part of internet service network.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eMounting holes\u003c\/strong\u003e allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003cul class=\"a-vertical a-spacing-none\"\u003e\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000 (GbE) and High PoE+ Networks\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe gigabit surge protector date rate of Gigabit 10\/100\/1000 (GbE) transfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network. POE Surge Protector allows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP303 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The lightning protector PoE supports both Mode A (Pins 1,2+ 3,6-) and B (7,8+ 4,5-) of the 802.3af standard. 802.3af (PoE) can deliver up to 15.4 watts per port with 12.95W at the powered device, while 802.3at (PoE+) can deliver up to 30 watts with 25.5 watts available to devices. PoE Plus is also known as High PoE.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe width=\"560\" height=\"315\" src=\"https:\/\/www.youtube.com\/embed\/7dFXvaW61LE\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet ground wire (11 Inch - 12 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw. The lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProtection Modes Line-Line, Line-Ground\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Line-to-Line ethernet surge protection mode helps protect against short circuits between different nodes of the network system while the Line-to-Ground mode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of 5KA defines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003cbr\u003e\u003cbr\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A bidirectional clamping on CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003cbr\u003e\u003cem\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eMultidirectional\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMaximum Discharge Current (8\/20μs): 10 KA\u003c\/li\u003e\n\u003cli\u003eNominal PoE voltage : \u0026lt;60V\u003c\/li\u003e\n\u003cli\u003ePoE current up to 2A\u003c\/li\u003e\n\u003cli\u003ePoE Mode Support Mode A and B for Power\u003c\/li\u003e\n\u003cli\u003eProtection Modes Line-Line, Line-Ground\u003c\/li\u003e\n\u003cli\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/li\u003e\n\u003cli\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/li\u003e\n\u003cli\u003eClamping Voltage Line-Line: 72 Volts\u003c\/li\u003e\n\u003cli\u003eImpedance 100 ohms\u003c\/li\u003e\n\u003cli\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/li\u003e\n\u003cli\u003eOutside Dimensions (W*L*H) 78*103*49 mm\u003c\/li\u003e\n\u003cli\u003eWeight: 110 g\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInvesting in a small, easy to install surge protector with all of the needed features and proven reliability can be the safest and most cost-effective solution for protecting your whole Ethernet network.\u003c\/p\u003e\n\u003ch4\u003e\u003cbr\u003e\u003c\/h4\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":42107829256388,"sku":"303x10","price":329.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/303x10.jpg?v=1677010281"},{"product_id":"outdoor-ethernet-thunder-lightning-surge-protector-for-poe-2-pack","title":"Outdoor Ethernet Thunder Lightning Surge Protector for PoE+ Gigabit 1000Mbs (2 Pack)","description":"\u003cp\u003e\u003cstrong\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B0BV5S9PJQ\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\" alt=\"\"\u003e\u003c\/a\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cstrong\u003eUPC: 850043852087\u003c\/strong\u003e\u003cbr\u003e\u003cem\u003eModel Number: TP303x2\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOutdoor Ethernet Surge Protector\u003c\/strong\u003e is a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage of electronic networking equipment. It can be mounted outside, and it's resistant to weather conditions (weatherproof IP44). It comes in the box enclosure which can be secured with a lock (not included).\u003cbr\u003e\u003cbr\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eGas discharge tubes (GDTs)\u003c\/strong\u003e are developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrestor so it provides a rigorous spark discharge control performance.\u003cbr\u003e\u003cbr\u003eEthernet Surge Suppressor TP303 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires). Gas discharge tubes dissipate the voltage transient through a contained plasma gas which harnesses excess voltage in the incoming power and releases it safely. It ensures the safety of a wide array of valuable components such as switch, router, modem, bridge, repeater, or any part of internet service network.\u003cbr\u003e\u003cbr\u003e\u003cstrong\u003eMounting holes\u003c\/strong\u003e allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003cul class=\"a-vertical a-spacing-none\"\u003e\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000 (GbE) and High PoE+ Networks\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe gigabit surge protector date rate of Gigabit 10\/100\/1000 (GbE) transfer supports an ultra-fast maximum data rate of 1 Gigabit per second (Gbps - 1000 Mbps) and does not affect the speed performance in the local area network. POE Surge Protector allows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP303 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages. The lightning protector PoE supports both Mode A (Pins 1,2+ 3,6-) and B (7,8+ 4,5-) of the 802.3af standard. 802.3af (PoE) can deliver up to 15.4 watts per port with 12.95W at the powered device, while 802.3at (PoE+) can deliver up to 30 watts with 25.5 watts available to devices. PoE Plus is also known as High PoE.\u003c\/p\u003e\n\u003cdiv class=\"responsive-video\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/7dFXvaW61LE\" height=\"315\" width=\"560\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet ground wire (11 Inch - 12 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw. The lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eProtection Modes Line-Line, Line-Ground\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Line-to-Line ethernet surge protection mode helps protect against short circuits between different nodes of the network system while the Line-to-Ground mode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of 5KA defines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003cbr\u003e\u003cbr\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A bidirectional clamping on CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003cbr\u003e\u003cem\u003e\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003eMultidirectional\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMaximum Discharge Current (8\/20μs): 10 KA\u003c\/li\u003e\n\u003cli\u003eNominal PoE voltage : \u0026lt;60V\u003c\/li\u003e\n\u003cli\u003ePoE current up to 2A\u003c\/li\u003e\n\u003cli\u003ePoE Mode Support Mode A and B for Power\u003c\/li\u003e\n\u003cli\u003eProtection Modes Line-Line, Line-Ground\u003c\/li\u003e\n\u003cli\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/li\u003e\n\u003cli\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/li\u003e\n\u003cli\u003eClamping Voltage Line-Line: 72 Volts\u003c\/li\u003e\n\u003cli\u003eImpedance 100 ohms\u003c\/li\u003e\n\u003cli\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/li\u003e\n\u003cli\u003eOutside Dimensions (W*L*H) 78*103*49 mm\u003c\/li\u003e\n\u003cli\u003eWeight: 110 g\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eInvesting in a small, easy to install surge protector with all of the needed features and proven reliability can be the safest and most cost-effective solution for protecting your whole Ethernet network.\u003c\/p\u003e\n\u003ch4\u003e\u003cbr\u003e\u003c\/h4\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":42107829649604,"sku":"303x2","price":68.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/products\/303x2.jpg?v=1677010299"},{"product_id":"tupavco-tp325-ethernet-surge-protector-2-5-gigabit-poe-150w-gas-discharge-tube","title":"Tupavco TP325 Ethernet Surge Protector \/ 2.5 Gigabit PoE++ 150W \/ Gas Discharge Tube","description":"\u003ch4\u003e\n\u003ca href=\"https:\/\/www.amazon.com\/dp\/B00805VUD8\"\u003e\u003c\/a\u003e\u003ca href=\"https:\/\/www.amazon.com\/\/dp\/B0FF81PCNH\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\" alt=\"\"\u003e\u003c\/a\u003e\n\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: 850043852124\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP325\u003c\/em\u003e\n\u003c\/h4\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan class=\"a-text-bold\"\u003e\u003cu\u003eDouble Speed (2.5 Gigabit) \u0026amp; Double Protection (GDT+TVS)\u003c\/u\u003e\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003e2.5 Gigabit Ethernet Surge Protector (GDT+TVS)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eis a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage to electronic networking equipment.\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eGas discharge tubes (GDTs)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eare developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrester so it provides a rigorous spark discharge control performance.\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eTransient Voltage Suppressors\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(TVS diodes)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eoffer a very fast response time, often in the picosecond range and clamp the voltage at a lower level providing better protection for sensitive electronic components.\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003c\/p\u003e\n\u003cp\u003eEthernet Surge Suppressor TP302 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires).\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eMounting flange\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon the both sides of lightning suppressor allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000\/2500 (GbE) and High PoE++ Networks\u003c\/h3\u003e\n\u003cp\u003eThe gigabit surge protector data rate of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e2.5\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eGigabit 10\/100\/1000\/2500 (GbE)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003etransfer supports an ultra-fast maximum data rate of 2.5 Gigabit per second (Gbps - 2500Mbps) and does not affect the speed performance in the local area network.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ePOE Surge Protector\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eallows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP302 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages.\u003c\/p\u003e\n\u003cp\u003eThe lightning protector PoE supports both\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eMode\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eA (Pins 1,2+ 3,6-) and B\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(7,8+ 4,5-)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eof the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003estandard.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af (PoE)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 15.4 watts per port with 12.95W at the powered device, while\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3at (PoE+)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 30 watts with 25.5 watts available to devices. TP302 supports PoE++, also known as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eHigh Poe\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(IEEE 802.3bt\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003estandard), and allows a maximum PoE current of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e154W\/48V\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ewhen used on all 4 pairs.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eground wire\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e(12 Inch - 16 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/p\u003e\n\u003cp\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables. The arrester is housed in a\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ecast aluminum\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eenclosure. The metal housing allows\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eshielded\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003ecurrent to be passed through the metal case of the network surge protector.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Line\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eethernet surge protection mode helps protect against short circuits between different nodes of the network system while the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Ground\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003emode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e20KA\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003edefines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/p\u003e\n\u003cp\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ebidirectional clamping\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eSpecifications\u003c\/h3\u003e\n\u003ch4 class=\"a-spacing-mini a-color-secondary a-text-italic\"\u003eMultidirectional\u003c\/h4\u003e\n\u003cp class=\"a-spacing-base\"\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul class=\"a-unordered-list a-vertical\"\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eNominal Discharge Current (8\/20μs): 20 KA\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eNominal PoE voltage : \u0026lt;60V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003ePoE current: 1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003ePoE Mode Support Mode A and B for Power\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eClamping Voltage Line-Line: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eImpedance 100 ohms\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eOutside Dimensions (W*L*H) 26*26*70 mm\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eWeight: 60 g\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":45036631195844,"sku":"325","price":36.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/TP325.jpg?v=1766189408"},{"product_id":"tupavco-tp325-ethernet-surge-protector-2-5-gigabit-10-pack","title":"Tupavco TP325 Ethernet Surge Protector \/ 2.5 Gigabit PoE++ 150W \/ Gas Discharge Tube (10 Pack)","description":"\u003ch4\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B0FZY7VCXG\/\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\" alt=\"\"\u003e\u003c\/a\u003e\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: 850043852315\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP325x10\u003c\/em\u003e\n\u003c\/h4\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan class=\"a-text-bold\"\u003e\u003cu\u003eDouble Speed (2.5 Gigabit) \u0026amp; Double Protection (GDT+TVS)\u003c\/u\u003e\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003e2.5 Gigabit Ethernet Surge Protector (GDT+TVS)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eis a surge protection device (SPD) that is inserted inline on an RJ45 CAT6\/CAT5\/CAT5e cable to prevent damage to electronic networking equipment.\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eGas discharge tubes (GDTs)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003eare developed to overcome some of the disadvantages of diode-based protectors like energy handling capability and is suitable for almost all surge, whether high or low frequency, it can be intercepted by a gas discharge tube surge arrester so it provides a rigorous spark discharge control performance.\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eTransient Voltage Suppressors\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(TVS diodes)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eoffer a very fast response time, often in the picosecond range and clamp the voltage at a lower level providing better protection for sensitive electronic components.\u003c\/p\u003e\n\u003cp\u003ePowerful surges that the device protects against include direct lightning strikes, voltage spikes, or PoE overvoltages. Despite the primary protection (a direct strike to a line), the thunder arrestor also offers secondary protection, which will arrest EMF induced surges (nearby lightning ethernet).\u003c\/p\u003e\n\u003cp\u003eEthernet Surge Suppressor TP302 use a Gas Discharge Tube (GDT) on all 4 pairs (8 wires).\u003c\/p\u003e\n\u003cp\u003e\u003cspan class=\"a-text-bold\"\u003eMounting flange\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon the both sides of lightning suppressor allows easy mounting to a wall, network panel, cabinet, or rack attaching by screws (not included).\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eRJ45 Lightning Protection for Gigabit 10\/100\/1000\/2500 (GbE) and High PoE++ Networks\u003c\/h3\u003e\n\u003cp\u003eThe gigabit surge protector data rate of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e2.5\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eGigabit 10\/100\/1000\/2500 (GbE)\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003etransfer supports an ultra-fast maximum data rate of 2.5 Gigabit per second (Gbps - 2500Mbps) and does not affect the speed performance in the local area network.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ePOE Surge Protector\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eallows a single RJ-45 cable to provide both data connection and electric power to device such as wireless access point, IP and security camera, VoIP phone, computer and others. Surge Arrestor TP302 is designed to protect PSE (power-supply equipment) connected to a network from transient overvoltages.\u003c\/p\u003e\n\u003cp\u003eThe lightning protector PoE supports both\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eMode\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eA (Pins 1,2+ 3,6-) and B\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(7,8+ 4,5-)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eof the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003estandard.\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3af (PoE)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 15.4 watts per port with 12.95W at the powered device, while\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e802.3at (PoE+)\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ecan deliver up to 30 watts with 25.5 watts available to devices. TP302 supports PoE++, also known as\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eHigh Poe\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e(IEEE 802.3bt\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003estandard), and allows a maximum PoE current of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e154W\/48V\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003ewhen used on all 4 pairs.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eInstallation\u003c\/h3\u003e\n\u003cp\u003eThe Ethernet lightning arrestor must be properly grounded to work. The ethernet\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eground wire\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e(12 Inch - 16 AWG) on the surge protector needs to be connected to ground through the shortest path. Excess electricity will follow the path of least resistance. In most cases, a ground busbar on an electrical panel or network rack cabinet is already grounded and is typically the easiest way to ground the wire. Other options to ground RJ45 surge protector are grounding block on the breaker panel, grounding rod or terminal of the closest outlet by connecting the ground wire to circular grounding hole on the grounded outlet center screw.\u003c\/p\u003e\n\u003cp\u003eThe lightning arrestor can be used with unshielded twisted pair (UTP) or shielded (STP) cables. The arrester is housed in a\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ecast aluminum\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eenclosure. The metal housing allows\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eshielded\u003cspan\u003e \u003c\/span\u003e\u003c\/span\u003ecurrent to be passed through the metal case of the network surge protector.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/h3\u003e\n\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Line\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eethernet surge protection mode helps protect against short circuits between different nodes of the network system while the\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003eLine-to-Ground\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003emode protects against short circuits between the network node and the earth. As it is not known where the transient will happen, having both modes protected ensures damage is minimized. Nominal Discharge Current of\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003e20KA\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003edefines the peak value of the current that can be passed through the SPD having a waveshape of 8\/20μs microsecond where the RJ45 lightning arrestor remains functional after 15 surges.\u003c\/p\u003e\n\u003cp\u003eOnce the surge protector ethernet voltage exceeds its designed rating it “begins to clamp” and starts to conduct energy directly to the electrical grounding system. A\u003cspan\u003e \u003c\/span\u003e\u003cspan class=\"a-text-bold\"\u003ebidirectional clamping\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eon CAT5 surge protector allows levels above and below the reference voltage by clamping the voltage that can cause damage.\u003c\/p\u003e\n\u003ch3 class=\"a-spacing-mini\"\u003eSpecifications\u003c\/h3\u003e\n\u003ch4 class=\"a-spacing-mini a-color-secondary a-text-italic\"\u003eMultidirectional\u003c\/h4\u003e\n\u003cp class=\"a-spacing-base\"\u003eEthernet network surge protector works in both directions (IN\/OUT), so the source input signal cable can be connected to any side. It is not important which side the equipment is behind, however the surge protector will protect networking equipment only on the opposite side of where surge occurs. To protect devices on both sides, it is recommended to have one of the surge protectors on each end of the RJ45 cable in the network topology.\u003c\/p\u003e\n\u003cul class=\"a-unordered-list a-vertical\"\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eNominal Discharge Current (8\/20μs): 20 KA\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eNominal PoE voltage : \u0026lt;60V\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003ePoE current: 1.6 A \/ 2 pairs, 3.2 A \/ 4 pairs\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003ePoE Mode Support Mode A and B for Power\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eProtection Modes Line-Line, Line-Ground\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eTested standards IEC 61643-21, IEC61000-4-5\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eClamping Voltage Line-Ground: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eClamping Voltage Line-Line: 72 Volts\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eImpedance 100 ohms\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eOperating Temperature -40°C (-40°F) to +80°C (+176°F)\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eOutside Dimensions (W*L*H) 26*26*70 mm\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003e\u003cspan class=\"a-size-base\"\u003eWeight: 60 g\u003c\/span\u003e\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":45615118614724,"sku":"325x10","price":299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/Ethernet_surge_protector_325x10_212ff661-025d-422c-9282-65c379fb3fe0.jpg?v=1766189408"},{"product_id":"ethernet-surge-protector-din-rail-mounted-gigabit-compatible-with-poe-tupavco-tp209","title":"Ethernet Surge Protector DIN Rail Mounted Gigabit - Compatible with PoE++ - Tupavco TP209","description":"\u003ch4\u003e\u003ca href=\"https:\/\/www.amazon.com\/\/dp\/B0GJFNCD9J\"\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\"\u003e\u003c\/a\u003e\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: \u003cmeta charset=\"utf-8\"\u003e\n\u003cspan\u003e850043852155\u003c\/span\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP209\u003c\/em\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe Tupavco TP209 is a surge protection device that is inserted inline on an RJ45 CAT5\/CAT6\/CAT7 cable, preventing damage to your network equipment. Easily mountable on any standard 19\" DIN rail in minutes!\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eIt will protect from any voltage spikes such as direct lightning spikes or overvoltages, lowering the voltage to a manageable \u0026lt;30V. It is compatible with IEEE 802.3AT standards and compatible with up to 1000 Mbps and PoE++ technology, ensuring that plugging it into your network will give you peace of mind without losing function. Its low 0.2 dB insertion loss ensures that there is minimal latency or lag added to your network.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eIts compact and durable design makes it perfect for all applications. Installation is easy, as you simply plug in your lines and are ready to go. Perfect for protecting a various array of devices, from IP cameras to servers and computers. Keep your expensive network components safe without compromising performance!\u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eGigabit and PoE++ Compatibility\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge protector supports data rates of 1000 Mbps without slowing down the signal. The surge protector ensures device safety without sacrificing speed and performance with data rate transfers of up to 1 Gigabit per second. This means that you can have peace of mind about the safety of your devices without sacrificing speed for your local area network (LAN), or for any other applications such as a wireless access point, IP or security cameras, VoIP phone, server, or a personal computer. \u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge arrestor is also compatible with PoE++ (IEEE 802.3bt) standards, capable of delivering 41 watts of power to your devices with the same single RJ45 connection line (CAT5\/CAT6\/CAT6a\/CAT7) that transmits the network. Keeping things simple for your setup, this enables a single cable to provide both the network signal and the power to your devices, while also protecting them from high-voltage surge events. \u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eEasy Installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge protector is easily installed, being plug-and-play for your network setup. It is compatible with standard 19” DIN rails, simply clipping onto them. After that, it only needs a grounding wire connected for a ‘path of least resistance’ to dissipate the voltage of a surge event. In many cases, the network cabinet or bar is already grounded, and is the easiest connection for the ground wire. This device provides bidirectional transmission from both the IN\/OUT port. However, it is important to keep in mind that protection is applied to the equipment located downstream from the surge entry point. For complete end-to-end network protection, install a unit at both ends of the RJ45 link.\u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eSpecifications\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli aria-level=\"1\" dir=\"ltr\"\u003e\n\u003cp role=\"presentation\" dir=\"ltr\"\u003e\u003cspan\u003eWorking voltage - 48V (Power) \/ 5V (Network Signal)\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli aria-level=\"1\" dir=\"ltr\"\u003e\n\u003cp role=\"presentation\" dir=\"ltr\"\u003e\u003cspan\u003eRated current - 850mA\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli aria-level=\"1\" dir=\"ltr\"\u003e\n\u003cp role=\"presentation\" dir=\"ltr\"\u003e\u003cspan\u003eTransmission rate - 1000 Mbps\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli aria-level=\"1\" dir=\"ltr\"\u003e\n\u003cp role=\"presentation\" dir=\"ltr\"\u003e\u003cspan\u003eImpulse voltage (10\/700us) - 6kV (common-mode) \/ 2kV (differential-mode)\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli aria-level=\"1\" dir=\"ltr\"\u003e\n\u003cp role=\"presentation\" dir=\"ltr\"\u003e\u003cspan\u003eClamping voltage - \u0026lt;30V\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli aria-level=\"1\" dir=\"ltr\"\u003e\n\u003cp role=\"presentation\" dir=\"ltr\"\u003e\u003cspan\u003eInsertion loss - \u0026lt;0.2dB\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli aria-level=\"1\" dir=\"ltr\"\u003e\n\u003cp role=\"presentation\" dir=\"ltr\"\u003e\u003cspan\u003eResponse time - \u0026lt;1ns\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":45864401043652,"sku":"209","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/E_cam_V02.jpg?v=1773191636"},{"product_id":"24-port-rackmount-ethernet-surge-protector-compatible-with-poe-and-gigabit-tupavco-tp224","title":"24 Port Rackmount Ethernet Surge Protector - Compatible with PoE++ and Gigabit - Tupavco TP224","description":"\u003ch4\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B0GM2QP9TD\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\" alt=\"\"\u003e\u003c\/a\u003e\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: \u003cmeta charset=\"utf-8\"\u003e\n\u003cspan\u003e850043852179\u003c\/span\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP224\u003c\/em\u003e\n\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe Tupavco TP224 is a surge protection device that is inserted inline on an RJ45 CAT5\/CAT6\/CAT7 cable, preventing damage to your network equipment. It has 24 functioning ports for device protection.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eBuilt to protect from any voltage spikes such as direct lightning spikes or overvoltages, lowering the voltage to a manageable \u0026lt;15V. It is compatible with IEEE 802.3AT standards and compatible with up to 1000 Mbps and PoE++ technology, ensuring that plugging it into your network will give you peace of mind without losing function.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eIts low 0.2 dB insertion loss ensures that there is minimal latency or lag added to your network. Its compact and durable design makes it perfect for all applications. Installation is easy, as you simply plug in your lines and are ready to go. Perfect for protecting a various array of devices, from IP cameras to servers and computers. Keep your expensive network components safe without compromising performance!\u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eProtecting 24 lines of network cabling at once, the TP204 can keep all the parts of your network protected from high-voltage spikes, without slowing down your connection and compromising performance. It can fit right into your setup with PoE++ compatibility, low latency, high data transfer rates and easy installation. Compatible with any standard 19” network racks, with easy mounting via flange screws.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eGigabit and PoE++ Compatibility\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge protector supports data rates of 1000 Mbps without slowing down the signal. The surge protector ensures device safety without sacrificing speed and performance with data rate transfers of up to 1 Gigabit per second.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThis means that you can have peace of mind about the safety of your devices without sacrificing speed for your local area network (LAN), or for any other applications such as a wireless access point, IP or security cameras, VoIP phone, server, or a personal computer. \u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge arrestor is also compatible with PoE++ (IEEE 802.3bt) standards, capable of delivering 41 watts of power to your devices with the same single RJ45 connection line (CAT5\/CAT6\/CAT6A\/CAT7) that transmits the network.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eKeeping things simple for your setup, this enables a single cable to provide both the network signal and the power to your devices, while also protecting them from high-voltage surge events.\u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eEasy Installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge protector is easily installed, being plug-and-play for your network setup. After that, it only needs a grounding wire connected for a ‘path of least resistance’ to dissipate the voltage of a surge event. In many cases, the network cabinet or bar is already grounded, and is the easiest connection for the ground wire. This device provides bidirectional transmission from both the IN\/OUT port. However, it is important to keep in mind that protection is applied to the equipment located downstream from the surge entry point. For complete end-to-end network protection, install a unit at both ends of the RJ45 link.\u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eWorking voltage - 48V (Power) \/ 5V (Network Signal)\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eRated current - 300mA\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eTransmission rate - 1000 Mbps\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eMax discharge current (8\/20us) - 5 kA\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eClamping voltage - \u0026lt;15V\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eInsertion loss - \u0026lt;0.2dB\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eResponse time - \u0026lt;1ns\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":45991523287236,"sku":"224","price":378.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/TP22424PortEthernetSurgeProtector1.jpg?v=1774632699"},{"product_id":"outdoor-gigabit-ethernet-surge-protector-waterproof-tupavco-tp206","title":"Outdoor Gigabit Ethernet Surge Protector - Waterproof and Compatible with PoE++ Tupavco TP206","description":"\u003ch4\u003e\n\u003ca href=\"https:\/\/www.amazon.com\/dp\/B0GWNJBNJ4\"\u003e\u003c\/a\u003e\u003ca href=\"https:\/\/www.amazon.com\/dp\/B0GKQYB78Q\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\" alt=\"\"\u003e\u003c\/a\u003e\n\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: 850043852148\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP206\u003c\/em\u003e\n\u003c\/h4\u003e\n\u003cp class=\"a-spacing-base\"\u003eThe Tupavco TP206 is a surge protection device that is inserted inline on an RJ45 CAT5\/CAT6\/CAT7 cable, preventing damage to your network equipment. It will protect from any voltage spikes such as direct lightning spikes or overvoltages, lowering the voltage to a manageable \u0026lt;30V.\u003c\/p\u003e\n\u003cp class=\"a-spacing-base\"\u003eIt is compatible with IEEE 802.3AT standards and compatible with up to 1000 Mbps and PoE++ technology, ensuring that plugging it into your network will give you peace of mind without losing function. Its low 0.2 dB insertion loss ensures that there is minimal latency or lag added to your network. Its compact and durable design makes it perfect for all applications.\u003c\/p\u003e\n\u003cp class=\"a-spacing-base\"\u003eInstallation is easy, as you simply plug in your lines and are ready to go. Perfect for protecting a various array of devices, from IP cameras to servers and computers. Keep your expensive network components safe without compromising performance!\u003c\/p\u003e\n\u003cdiv class=\"celwidget aplus-module 3p-module-b aplus-standard\" data-csa-c-id=\"3u9j17-xr1llk-3rzmdo-vl1kqb\" data-cel-widget=\"aplus-3p-module-b\"\u003e\n\u003cdiv class=\"aplus-module-wrapper aplus-3p-fixed-width\"\u003e\n\u003cp class=\"a-spacing-base\"\u003eBuilt for outdoor applications, this ethernet surge arrestor is designed to withstand storms, rains, and any other extreme weather. In the case of storms, you will appreciate the peace of mind that the TP206 gives to you, knowing your network is safe from lightning. Therefore, it is perfect to link remote outdoor connections of cameras or secondary servers to your network.\u003c\/p\u003e\n\u003cp class=\"a-spacing-base\"\u003eThe surge protector supports data rates of 1000 Mbps without slowing down the signal. The surge protector ensures device safety without sacrificing speed and performance with data rate transfers of up to 1 Gigabit per second.\u003c\/p\u003e\n\u003cp class=\"a-spacing-base\"\u003eThis means that you don’t have to worry about the safety of your devices without sacrificing speed for your local area network (LAN), or for any other applications such as a wireless access point, IP or security cameras, VoIP phone, server, or a personal computer.\u003c\/p\u003e\n\u003cdiv class=\"celwidget aplus-module 3p-module-b aplus-standard\" data-csa-c-id=\"928q44-xiaznj-jnwbq7-fazrvd\" data-cel-widget=\"aplus-3p-module-b\"\u003e\n\u003cdiv class=\"aplus-module-wrapper aplus-3p-fixed-width\"\u003e\n\u003cp class=\"a-spacing-base\"\u003eThe surge arrestor is also compatible with PoE++ (IEEE 802.3bt) standards, capable of delivering 41 watts of power to your devices with the same single RJ45 connection line (CAT5\/CAT6\/CAT6A\/CAT7) that transmits the network. Keeping things simple for your setup, this enables a single cable to provide both the network signal and the power to your devices, while also protecting them from high-voltage surge events.\u003c\/p\u003e\n\u003cp class=\"a-spacing-base\"\u003eThe surge protector is easily installed, being plug-and-play for your network setup. After that, it only needs a grounding wire connected for a ‘path of least resistance’ to dissipate the voltage of a surge event. In many cases, the network cabinet or bar is already grounded, and is the easiest connection for the ground wire.\u003c\/p\u003e\n\u003cp class=\"a-spacing-base\"\u003eThis device provides bidirectional transmission from both the IN\/OUT port. However, it is important to keep in mind that protection is applied to the equipment located downstream from the surge entry point. For complete end-to-end network protection, install a unit at both ends of the RJ45 link.\u003c\/p\u003e\n\u003cp class=\"a-spacing-base\"\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul class=\"a-unordered-list a-vertical\"\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003eWorking voltage - 48V (Power) \/ 5V (Network Signal)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003eRated current - 800mA\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003eTransmission rate - 1000 Mbps\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003eImpulse voltage (10\/700us) - 6kV (common-mode) \/ 2kV (differential-mode)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003eClamping voltage - \u0026lt;30V\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003eInsertion loss - \u0026lt;0.2dB\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan class=\"a-list-item\"\u003eResponse time - \u0026lt;1ns\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":46105261801668,"sku":"206","price":39.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/TP206OutdoorEthernetSurgeProtector3.jpg?v=1777592539"},{"product_id":"ethernet-surge-protector-poe-gigabit-tupavco-tp202","title":"Ethernet Surge Protector - PoE++ Gigabit - Tupavco TP202","description":"\u003ch4\u003e\u003ca href=\"https:\/\/www.amazon.ca\/dp\/B0GL9NB8XN\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/ViewOnAmazon.png?v=1738177868\" alt=\"\"\u003e\u003c\/a\u003e\u003c\/h4\u003e\n\u003ch4\u003e\n\u003cstrong\u003eUPC: \u003cmeta charset=\"utf-8\"\u003e\n\u003cspan\u003e850043852131\u003c\/span\u003e\u003cbr\u003e\u003c\/strong\u003e\u003cem\u003eModel Number: TP202\u003c\/em\u003e\n\u003c\/h4\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe Tupavco TP202 is a surge protection device that is inserted inline on an RJ45 CAT5\/CAT6\/CAT7 cable, preventing damage to your network equipment. It will protect from any voltage spikes such as direct lightning spikes or overvoltages, lowering the voltage to a manageable \u0026lt;30V. It is compatible with IEEE 802.3AT standards and compatible with up to 1000 Mbps and PoE++ technology, ensuring that plugging it into your network will give you peace of mind without losing function. Its low 0.2 dB insertion loss ensures that there is minimal latency or lag added to your network. Its compact and durable design makes it perfect for all applications. Installation is easy, as you simply plug in your lines and are ready to go. Perfect for protecting a various array of devices, from IP cameras to servers and computers. Keep your expensive network components safe without compromising performance!\u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eGigabit and PoE++ Compatibility\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge protector supports data rates of 1000 Mbps without slowing down the signal. The surge protector ensures device safety without sacrificing speed and performance with data rate transfers of up to 1 Gigabit per second. This means that you can have peace of mind about the safety of your devices without sacrificing speed for your local area network (LAN), or for any other applications such as a wireless access point, IP or security cameras, VoIP phone, server, or a personal computer. \u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge arrestor is also compatible with PoE++ (IEEE 802.3bt) standards, capable of delivering 48 watts of power to your devices with the same single RJ45 connection line (CAT5\/CAT6\/CAT6a\/CAT7) that transmits the network. Keeping things simple for your setup, this enables a single cable to provide both the network signal and the power to your devices, while also protecting them from high-voltage surge events. \u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eEasy Installation\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThe surge protector is easily installed, being plug-and-play for your network setup. After that, it only needs a grounding wire connected for a ‘path of least resistance’ to dissipate the voltage of a surge event. In many cases, the network cabinet or bar is already grounded, and is the easiest connection for the ground wire. This device provides bidirectional transmission from both the IN\/OUT port. However, it is important to keep in mind that protection is applied to the equipment located downstream from the surge entry point. For complete end-to-end network protection, install a unit at both ends of the RJ45 link.\u003c\/span\u003e\u003cb\u003e\u003c\/b\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eWorking voltage - 48V (Power) \/ 5V (Network Signal)\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eRated current - 850mA\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eTransmission rate - 1000 Mbps\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eImpulse voltage (10\/700us) - 6kV (common-mode) \/ 2kV (differential-mode)\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eClamping voltage - \u0026lt;30V\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eInsertion loss - \u0026lt;0.2dB\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli dir=\"ltr\" aria-level=\"1\"\u003e\n\u003cp dir=\"ltr\" role=\"presentation\"\u003e\u003cspan\u003eResponse time - \u0026lt;1ns\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Tupavco","offers":[{"title":"Default Title","offer_id":46105320259780,"sku":"202","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0067\/4506\/3491\/files\/TP202EthernetSurgeProtector1.jpg?v=1777594662"}],"url":"https:\/\/www.tupavco.com\/collections\/ethernet-surge-protectors\/rack-equipment.oembed","provider":"Tupavco","version":"1.0","type":"link"}